Bedienungsanleitung Bosch EasyCut 12 (Seite 14 von 93) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

765857

Zoom out

Zoom in

Vorherige Seite

1/93

Nächste Seite

14 | English

uDo not continue to press the On/Off switch after the

power tool has automatically switched off. The battery

can be damaged.

To remove the battery (5), press the release button (6) and

pull the battery back and out of the power tool. Do not use

force to do this.

Battery charge-control indicator

When the on/off switch(4) is pressed in halfway or com-

pletely, the battery charge indicator(8) indicates the bat-

tery's state of charge for a few seconds. It consists of an LED

which lights up in two colours.

LED Capacity

Lit green ≥ 30%

Lit red <30%

Flashing redA) 0%

A) The battery charge indicator will also flash red if the battery has

overheated or overloaded.

Inserting/changing the saw blade

uWhen fitting or changing the saw blade, wear protect-

ive gloves. Blades are sharp and can become hot when

used for prolonged periods of time.

uTake care not to hold the power tool close to the on/

off switch or by the on/off switch and lock-off button

when changing the saw blade. There is risk of injury

from unintentionally pressing the on/off switch.

uAvoid contact with the skin when changing a saw

blade and use protective gloves in perfect condition.

The saw blade can become hot when in operation for a

long time.

uDo not pull on the chain and do not pull the chain off

the guide unit.

Always replace a complete saw blade with another complete

saw blade. The chain cannot be replaced on its own.

Selecting the saw blade

Only use saw blades that are suitable for the material you are going to cut. The saw blade should not be longer than required

for the cut you want to make.

Saw blade Cutting depth Order number Materials

NanoBlade Wood Basic 50mm 2 609 256 D83 Wood, plastic (PVC, PC, PMMA)

NanoBlade Wood Speed 50mm 2 609 256 D84 Wood, plastic (PVC, PC, PMMA)

NanoBlade Wood Speed 65mm 2 609 256 D86 Wood, plastic (PVC, PC, PMMA)

Inserting the saw blade (seefigureA)

uUse only clean saw blades. Make sure that the saw

blade receptacle is free of chips and sawdust.

Use the locking lever(10) to open the cover(9) of the saw

blade receptacle. Insert the saw blade as shown in the fig-

ure. Make sure that the drive shaft and the end of the saw

blade fit in the recess on the saw blade receptacle(12).

Close the cover of the saw blade receptacle and lock it with

the locking lever. You should hear the locking lever click into

place.

The chain of the saw blade is tensioned automatically.

If the chain slips through or becomes detached from the

guide unit, open and close the cover(9) of the saw blade re-

ceptacle.

Removing the saw blade

Open the locking lever(10) fully open the cover(9) of the

saw blade receptacle. Remove the saw blade.

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some

wood types, minerals and metal can be harmful to one’s

health. Touching or breathing-in the dust can cause allergic

reactions and/or lead to respiratory infections of the user or

bystanders.

Certain dust, such as oak or beech dust, is considered carci-

nogenic, especially in connection with wood-treatment ad-

ditives (chromate, wood preservative). Materials containing

asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the ma-

terials to be worked.

uAvoid dust accumulation at the workplace. Dust can

easily ignite.

Operation

uNever bend the saw blade

Starting Operation

Inserting the battery

Note: The use of batteries unsuitable for your power tool can

lead to malfunctions or damage to the power tool.

Insert the charged battery(5) into the battery receptacle un-

til you feel it engage and it is securely locked in place.

Switching on/off

To switch on the power tool, press the lock-off button(3) to

the left or right. Then press the on/off switch (4) and keep it

pressed.

Once the power tool is switched on, you can release the lock-

off button(3).

To switch off the power tool, release the on/off switch (4).

1 609 92A 6XB | (07.07.2021) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch EasyCut 12 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info