Bedienungsanleitung Bosch EasyPump (Seite 13 von 175) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

766861

Zoom out

Zoom in

Vorherige Seite

1/175

Nächste Seite

English | 13

Typically, the A-weighted sound pressure level of the power

tool is71dB(A). Uncertainty K=3dB. The noise level when

working can exceed the volume stated. Wear hearing pro-

tection!

Vibration total values ah (triax vector sum) and uncertainty K

determined according to EN62841‑1:

ah=4m/s2, K=1.5m/s2.

The vibration level and noise emission value given in these

instructions have been measured in accordance with a

standardised measuring procedure and may be used to com-

pare power tools. They may also be used for a preliminary

estimation of vibration and noise emissions.

The stated vibration level and noise emission value repres-

ent the main applications of the power tool. However, if the

power tool is used for other applications, with different ap-

plication tools or is poorly maintained, the vibration level

and noise emission value may differ. This may significantly

increase the vibration and noise emissions over the total

working period.

To estimate vibration and noise emissions accurately, the

times when the tool is switched off or when it is running but

not actually being used should also be taken into account.

This may significantly reduce vibration and noise emissions

over the total working period.

Implement additional safety measures to protect the oper-

ator from the effects of vibration, such as servicing the

power tool and application tools, keeping their hands warm,

and organising workflows correctly.

Assembly

Battery Charging (seefigureA)

uUse only the power supplies listed in the technical

data. Only these power supplies are matched to the lith-

ium-ion battery of your air pump.

Note: The battery is supplied partially charged. To ensure

the maximum performance of the battery, use the power

supply to fully charge the battery before first use.

The lithium-ion battery can be charged at any time without

reducing its service life. Interrupting the charging process

does not damage the battery.

The lithium-ion battery is protected against deep discharge

by "Electronic Cell Protection (ECP)". A protective circuit

switches the air pump off when the battery is drained.

uDo not continue to press the on/off button after the

air pump has automatically switched itself off due to

an empty battery. This can damage the rechargeable

battery.

To charge the battery, connect the USBType-C® port(16) to

the power supply(15) via the USB cable(14). Plug the

power supply into a plug socket.

The charging process will begin and will be indicated by con-

tinuously filling bars in the battery charge indicator(d). The

air pump cannot be used during charging.

When the charging process is complete, the battery charge

indicator(d) will be continuously lit until the air pump is dis-

connected from the power supply.

If you are not planning to use the air pump again soon, dis-

connect the power supply(15) from the mains.

Battery Charge Indicator

The battery charge indicator(d) in the display shows the

battery's state of charge:

Display Capacity

75−100%

50−75%

25−50%

5−25%

0−5%

Fitting/Changing the Adapter (seefigureB)

Select the adapter best suited to the intended application:

– Valve adapter(2), e.g. for many bike valves.

– Ball needle adapter(3), e.g. for footballs.

– Volume adapter(4), for small beach items or sporting

goods, e.g. beach balls.

Slide the lid off the adapter storage compartment(1) and re-

move the adapter.

Screw the adapter fully into the pressure hose(9).

For standard car tyre valves (sometimes also used on bikes),

no adapter is required.

Operation

Starting Operation

Switching On and Off

To switch the air pump on or off, press the on/off

button(5). The last set target pressure is saved when

switching off the pump.

When no button on the air pump is pressed for approx.

3minutes, the air pump automatically switches off to pre-

serve battery life.

Switching the worklight on and off

To switch the worklight(12) on and off, press the change

unit/worklight button(7) for approximately 1 second.

uDo not look directly into the worklight; it can blind

you.

Changing the Unit of Measurement

For the pressure indicator, the units bar, psi and kPa are

available.

To change the unit of measurement, short press the change

unit/worklight button(7) as many times as needed until the

required unit of measurement appears in the unit of meas-

urement indicator(a).

Bosch Power Tools 1 609 92A 6UH | (10.06.2021)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch EasyPump Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info