Bedienungsanleitung Bosch EasyVac 3 (Seite 12 von 114) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

766884

Zoom out

Zoom in

Vorherige Seite

1/114

Nächste Seite

12 | English

1 609 92A 43U | (6.9.17) Bosch Power Tools

17 Lid of the dust cup

18 Dust bag

19 Dust bag holder

20 Air diffuser

21 Fabric filter

22 Flat-pleated filter

23 Exhaust air cover

24 Permanent filter

*Accessories shown or described are not part of the standard de-

livery scope of the product. A complete overview of accessories

can be found in our accessories program.

Technical Data

Assembly

Before any work on the vacuum cleaner itself, pull the

mains plug.

Mounting the Vacuum Hose (see figure A)

– Insert the vacuum hose 10 into the hose connection piece

7 and turn it all the way in clockwise direction.

Mounting VAC Accessories

The vacuum hose 10 is equipped with a clip system, with

which the VAC accessories (extraction adapter 12, curved

nozzle 11) can be connected.

Fitting the extraction adapter or curved nozzle

(see figure B)

– Fit the extraction adapter 12 or the curved nozzle 11 to the

vacuum hose 10 until the two snap fasteners 15 of the vac-

uum hose click into place.

– To disassemble, press both snap-fasteners 15 inward and

pull the components apart.

Mounting the suction nozzles

–Then attach the required vacuuming accessory (floor noz-

zle, crevice nozzle, etc.) firmly to the curved nozzle 11 or

the extraction adapter 12.

Replacing/Inserting the Dust Bag

(see figures C1 – C4)

For vacuuming fine dust, which is generated when working

with sanders, drills or fine saw blades, you should use a dust

bag (accessory). This makes the dust easier to dispose of.

Chips, which are generated when working with larger saws, or

coarser dirt can be vacuumed without using a dust bag. When

doing so, you should clean the fabric filter 21 occasionally

(see “Cleaning the Filter Assembly”, page 13).

Replacing/Inserting the Dust Bag (Accessory)

– Press the release button 8 and pull the dust cup 9 out of

the vacuum cleaner.

– Grip the lid 17 at the connection flange 16 and remove the

lid from the dust cup.

– Turn the lid 17 over.

–Put the dust bag 18 over the connection flange 16 of the

vacuum cleaner and turn the cardboard flaps under the

dust bag holder 19.

– Press the lid 17 back onto the dust cup 9 and then slide the

dust cup back into the vacuum cleaner until it clicks into

place.

– To remove a full dust bag 18, twist it off the connection

flange 16 in a downward direction – without turning the

lid 17 over.

Operation

Before any work on the vacuum cleaner itself, pull the

mains plug.

Starting Operation

Observe correct mains voltage! The voltage of the pow-

er source must agree with the voltage specified on the

nameplate of the vacuum cleaner. Equipment marked

with 230 V can also be operated with 220 V.

Only use an undamaged filter (no cracks, small holes,

etc.). Replace a damaged filter immediately.

Products sold in AUS and NZ only: Use a residual current de-

vice (RCD) with a rated residual current of 30 mA or less.

To save energy, only switch the vacuum cleaner on when us-

ing it.

To ensure optimal vacuuming performance, always complete-

ly unwind the vacuum hose 10 from the vacuum cleaner lid .

Vacuuming of deposited dust

Dry vacuum cleaner EasyVac 3

Article number 0 603 3D1 0..

Rated voltage V 220–240

Rated power input W 700

Frequency Hz 50/60

Container volume (gross) l2.1

Vacuum (turbine), max. mbar 240

Airflow (turbine), max. l/s 35

Weight according to EPTA-

Procedure 01:2014 kg 4.3

Protection class /I

The values given are valid for nominal voltages [U] of 230 V. For lower

voltage and models for specific countries, these values can vary.

Automatic Start/Stop feature*

Rated voltage max. power

output min. power

output

EU/AUS 220–240 V 2000 W 100 W

UK 220–240 V 1800 W 100 W

* Specification of the allowable load of the connected power tool (coun-

try-specific)

–To switch on the vacuum cleaner, set the

mode selector switch 2 to the “Vacuuming”

symbol.

–To switch off the vacuum cleaner, set the

mode selector switch 2 to the “Off” symbol.

OBJ_BUCH-2992-002.book Page 12 Wednesday, September 6, 2017 11:43 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch EasyVac 3 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info