Bedienungsanleitung Bosch FR 100 (Seite 22 von 88) (Englisch)

458017

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

6 720 645 347 (2010/09)

22 | Operation

– Off: the built-in plate heat exchanger in the

heating appliance is not kept constantly

hot (eco mode); as a result energy is saved.

In eco mode, the hot tap has to be run for

a short while before the water becomes

hot.

• If the DHW cylinder and FR 100 are directly

connected to the heating appliance, the DHW

program switches between the following

operating modes:

– On: Cylinder heating enabled (temperature

in accordance with setting on heating

appliance).

– Off: Cylinder heating blocked.

• With appliances connected to a DHW cylinder

and FR 110, the DHW program specifies the

required water temperature (set

temperature).

– If the temperature measured in the DHW

cylinder is below the set temperature, the

cylinder is reheated.

– Once the set temperature is reached (or

exceeded), cylinder reheating is stopped.

DHW circulation program

The DHW circulation program specifies when a

connected DHW circulation pump for domestic

hot water runs.

5.2 Setting programs

5.2.1 Display views and menu navigation

The user interface of the FR 100 / FR 110 room

temperature-dependent heating controller is

implemented as a so-called "menu". Within that

menu, the various functions are arranged in a

hierarchical structure. For greater clarity, the

menu is subdivided into three sections (MAIN

MENU, INFO, INSTALLER SETTINGS). Each

section can be accessed by its own button. The

entire menu structure is shown in tabular form in

chapters 6.1, 7 and 8.1.

To navigate through the menu:

• Press to open MAIN MENU. From any

point within the MAIN MENU, press to

go back to the standard display.

• Press to open the INFO menu. From any

point within the INFO menu, press to go

back to the standard display.

• Hold down for at least 3 seconds to open

the INSTALLER SETTINGS menu. From any

point within the INSTALLER SETTINGS menu,

press to go back to the standard display.

• The selected menu point/parameter is

displayed in colours, i.e. white on

black.

• Arrows in the left margin indicate that there is

more information than can be shown on the

display at once. It can be viewed with .

• opens the submenu associated with the

selected menu point/parameter or activates

editing mode for the parameter (the

parameter setting starts flashing).

If the DHW program changes from a

higher to a lower temperature, the

water in the cylinder will not

immediately cool to the lower

temperature, i.e. water at a higher

temperature will continue to be

available for some time. However,

the cylinder will not be reheated

until the temperature falls below

the new set temperature.

The functions of the controls and the

meanings of the symbols on the

display are explained on pages 2

and 3.

info

inverse

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch FR 100 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch FR 100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info