Bedienungsanleitung Bosch FR 110 (Seite 73 von 88) (Englisch)

458018

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

6 720 645 347 (2010/09)

Energy saving tips | 73

10 Energy saving tips

• The temperature in the lead room (where the

controller is fitted) acts as a guide for the

heating circuit to which the controller is

assigned. Therefore, set the output of the

radiators inside the lead room as low as

possible:

– For manual valves via preselection.

– With fully opened thermostatic valves via

the return fitting.

If the thermostatic valves in the lead room

are not fully open, they may reduce the

heat supply even though the controller

requests heat.

• Regulate the temperature in adjacent rooms

via thermostatic valves.

• External heat in the lead room (e.g. solar

radiation, stove etc.) can result in too little

heating in adjacent rooms (the heating system

remains cold).

• Make effective use of the temperature levels

and switching times by setting them to suit

the preferences of the occupants.

– Comfort = For a comfortable living

environment

– Economy = For an active living

environment

– Frost = For when away or asleep

• Much energy can be saved by reducing the

room temperature via economy phases.

Reducing the room temperature by 1 K ( °C)

enables up to 5% energy to be saved.

It is not recommended to let the room

temperature of heated rooms fall below

+15 °C during the daytime, otherwise the

cooled-down walls continue to radiate cold

and the room temperature rises higher,

leading to higher energy consumption than if

an even heat supply is applied.

• Good thermal insulation of the building: the

set temperature for Economy is never

reached. Nevertheless energy is being saved

as the heating system stays off.In that case set

the switching point for Economy to an earlier

time.

• Don't keep windows slightly open for

ventilation. This leads to a constant extraction

of heat from the room without noticeably

improving the ambient air in the room.

• Vent briefly but intensively (open window

fully).

• When ventilating, turn off the thermostatic

valve or set the operating mode selector to

Frost.

• Make effective use of the temperature levels

and switching times for the domestic hot

water by setting them to suit the preferences

of the occupants.

If heat-up optimisation is switched on:

• To make best use of heat-up optimisation, set

the times for heating up to the temperature

levels for Economy or Comfort as late as

possible.

• The heat-up optimisation function learns the

conditions in the lead room Æ chapter 8.3 on

page 59.

The first time heat-up optimisation is used,

there may be significant temperature

differences. During the initial learning phase,

do not change the setting before heat-up is

complete. After a few days, the learning

process will have advanced and the control

accuracy will improve.

• Set the temperature for Economy or Frost

low as possible.

• During Economy or Frost the lead room

conditions must remain constantly the same

Æ chapter 8.3 on page 59.

If the conditions change, it can take several

days for heat-up optimisation to adapt to the

new conditions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch FR 110 Seite 73

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch FR 110

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info