Bedienungsanleitung Bosch GAM 270 MFL (Seite 19 von 331) (Alle Sprachen)

786514

Zoom out

Zoom in

Vorherige Seite

1/331

Nächste Seite

English | 19

Digital angle and grade measuring device GAM 270 MFL

IP 54 (dust and splash-proof) ●

A) The working range may be reduced by unfavourable environmental conditions

(e.g. direct sunlight).

B) Only non-conductive deposits occur, whereby occasional temporary conductivity

caused by condensation is expected.

C) Operating duration without laser

The serial number(13) on the type plate is used to clearly identify your measuring tool.

Assembly

Inserting/Replacing Batteries (seefigureA)

It is recommended that you use alkaline manganese or rechargeable batter-

ies to operate the measuring tool.

To open the battery compartment cover(5), press the locking

mechanism(6) and fold the battery compartment cover up. Insert the bat-

teries/rechargeable batteries.

When doing so, ensure that the polarity is correct and corresponds to the

diagram on the battery compartment cover.

Battery Indicator

The battery indicator(b) always indicates the current battery status:

Indicator Capacity

90–100 %

60–90 %

30–60 %

10–30 %

0–10 %

The empty battery indicator flashes. You can measure for ap-

proximately another 15–20min from when the flashing begins

until the tool shuts down.

Always replace all the batteries at the same time. Only use batteries from the

same manufacturer and which have the same capacity.

uTake the batteries out of the measuring tool when you are not using it

for a prolonged period of time. The batteries can corrode and self-dis-

charge during prolonged storage in the measuring tool.

uMake sure to switch the laser off before changing the batteries. An

accidentally switched on laser can blind other persons.

Mounting the Leg Extension

Slide the leg extension(21) from the front onto the fold-out leg(1). Slide

the leg extension as far as possible over the joint of the measuring tool.

Operation

Starting Operation

uProtect the measuring tool from moisture and direct sunlight.

uDo not expose the measuring tool to any extreme temperatures or

variations in temperature. For example, do not leave it in a car for ex-

tended periods of time. In case of large variations in temperature, allow

the measuring tool to adjust to the ambient temperature before putting it

into operation. The precision of the measuring tool may be compromised

if exposed to extreme temperatures or variations in temperature.

uKeep the supporting surfaces and contact edges of the measuring

tool clean. Protect the measuring tool against shock and impact. Dirt

particles or deformations can lead to faulty measurements.

uAvoid hard knocks to the measuring tool or dropping it. Always carry

out an accuracy check before continuing work if the measuring tool has

been subjected to severe external influences (see "Accuracy Check and

Calibration of the Measuring Tool", page23).

Switching On and Off

uNever leave the measuring tool unattended when switched on, and

ensure the measuring tool is switched off after use. Others may be

blinded by the laser beam.

To switch on the measuring tool, press the on/off button(14).

If the indicator H (a) lights up, a value from the last measurement is still

saved. This value can be deleted by briefly pressing the on/off button(14).

To switch off the measuring tool, press the on/off button(14).

When no activity is performed on the measuring tool for approx. 30min, the

measuring tool automatically switches off to save the batteries.

Aligning with the Spirit Levels

The measuring tool can be aligned horizontally with spirit level(9) and ver-

tically with spirit level(10).

The measuring tool can also be used as a carpenter’s spirit level for checking

vertical and horizontal lines. For this, place or hold the measuring tool

against the surface subject to checking.

Bosch Power Tools 1 609 92A 7M1 | (28.04.2022)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GAM 270 MFL Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info