Bedienungsanleitung Bosch GAS 35 H AFC (Seite 24 von 313) (Alle Sprachen)

786485

Zoom out

Zoom in

Vorherige Seite

1/313

Nächste Seite

24 | English

Vacuuming up liquids

– To switch on the dust extractor, set the mode selector

switch(7) to the "extraction" symbol.

The dust extractor is equipped with fill level sensors (40).

The dust extractor shuts down if the maximum fill level has

been reached. Set the mode selector switch (7) to the

"switch off" symbol.

Note: When extracting non-conductive liquids (e.g. drilling

emulsion, oils and fats), the dust extractor will not switch off

when the container is full. The fill level must be constantly

monitored and the container emptied in good time.

If the acoustic warning signal sounds during wet extraction,

the operating reliability of the dust extractor is not affected.

No measures to rectify the fault are necessary.

– To switch off the dust extractor, set the mode selector

switch(7) to the "switch off" symbol.

– To transport the dust extractor, screw the sealing plug(2)

onto the hose adapter(3).

– Empty the container(1).

To prevent mould growth after wet extraction:

– Remove the flat-pleated filter(28) and leave this to dry

thoroughly.

– Remove the top part of the dust extractor(12), open the

filter cover(39) and leave both elements to dry thor-

oughly.

Automatic filter cleaning (see figureH)

When automatic filter cleaning (AFC) is active, the flat-

pleated filter(28) is cleaned every 15 seconds using blasts

of air (pulsating noise).

The filter cleaning function should be activated at the very

latest when the suction power is no longer sufficient.

Regular use of the filter cleaning function will increase the

service life of the filter.

In order to achieve an optimum filter service life, deactivate

the automatic filter cleaning function only in exceptional

cases, e.g. when vacuuming pure liquids or using a safety fil-

ter bag.

A flat-pleated filter with surface dirt is still fully functional. It

is not necessary to clean the flat-pleated filter manually by

shaking or blowing it out; this may even damage the filter.

Note: The automatic filter cleaning function is switched on

by default when the dust extractor leaves the factory.

It is only possible to switch the automatic filter function on or

off when the tool is switched on.

–Deactivating AFC

Press the AFC button(9).

The control LED(37) will go out.

–Activating AFC

Press the AFC button(9).

The control LED(37) will light up green.

Maintenance and Service

Maintenance and Cleaning

uPull the plug out of the socket before cleaning or per-

forming maintenance on the vacuum cleaner, making

tool adjustments, changing accessories or putting

away the vacuum cleaner. This safety measure prevents

the vacuum cleaner from being started accidentally.

uTo ensure safe and efficient operation, always keep

the dust extractor and the ventilation slots clean.

In order to avoid safety hazards, if the power supply cord

needs to be replaced, this must be done by Bosch or by an

after-sales service centre that is authorised to repair Bosch

power tools.

uWear a protective mask of protection class FFP2 or

higher and disposable protective suit according to the

relevant provisions when carrying out maintenance

and cleaning of the dust extractor. Maintenance and

cleaning may only be carried out by persons with

proof of expertise.

The housing of the dust extractor must be thoroughly vacu-

umed and wiped clean with a damp cloth, or treated with

sealant, before the dust extractor can be removed from the

hazardous area. All dust extractor parts must be considered

to be contaminated when taken from the hazardous area, ap-

propriate precautions must be taken. All parts not suffi-

ciently cleaned during maintenance/repair must be disposed

of (in impermeable bags).

For the user to carry out maintenance, the dust extractor

needs to be disassembled, cleaned and maintained as far as

this is possible without endangering maintenance personnel

or other persons. Before disassembly, the dust extractor

should be cleaned to prevent any potential hazards. The pro-

cesses described in the Assembly chapter form part of the

maintenance routine. The room/enclosure in which the dust

extractor is disassembled should be well ventilated. Wear

personal protective equipment while carrying out mainten-

ance.

After completing maintenance, the maintenance area should

be cleaned.

A technical inspection must be carried out at least once a

year by the manufacturer or someone who has been trained,

e.g. to check for filter damage and to check that the dust ex-

tractor is tight and that the control unit is functioning cor-

rectly.

In addition to this, the effectiveness of the filter must be in-

spected at least annually in accordance with

EN60335-2-69, 22.AA.201.2.

National requirements may also necessitate more frequent

inspection.

If the filter is no longer deemed effective, it must be replaced

and the test must be repeated.

Removing/changing the flat-pleated filter (see figures

I1–I2)

The suction power is dependent on the condition of the fil-

ter. Therefore, the filter should be cleaned regularly.

1 609 92A 7Z8 | (23.06.2022) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GAS 35 H AFC Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info