Bedienungsanleitung Bosch GBH 18V-26 D (Seite 17 von 243) (Alle Sprachen)

786121

Zoom out

Zoom in

Vorherige Seite

1/243

Nächste Seite

English | 17

Battery model ProCORE18V...

LEDs Capacity

5× continuous green light 80−100%

4× continuous green light 60−80%

3× continuous green light 40−60%

2× continuous green light 20−40%

1× continuous green light 5−20%

1× flashing green light 0−5%

Auxiliary handle

uDo not operate your power tool without the auxiliary

handle(14).

Swivelling the auxiliary handle (see figure A)

You can swivel the auxiliary handle (14) to any angle for a

safe work posture that minimises fatigue.

– Turn the lower gripping end of the auxiliary handle (14)

anticlockwise and swivel the auxiliary handle (14) into

the required position. Then turn the lower gripping end of

the auxiliary handle (14) clockwise to retighten it.

Make sure that the retaining strap of the auxiliary handle

slots into the corresponding groove of the housing.

Selecting Drill Chucks and Tools

Hammer drilling and chiselling require SDS-plus application

tools that are inserted into the SDS-plus drill chuck.

For drilling without impact in wood, metal, ceramic and

plastic as well as for screwdriving, tools without SDS‑plus

are used (e.g. cylindrical shank drill bits). For these tools, a

keyless chuck or a keyed chuck are required.

Inserting/removing the keyed chuck

Fitting the keyed chuck (see figure B)

– Screw the SDS-plus shank (20) into a keyed chuck (19).

Secure the keyed chuck (19) using the securing screw

(18). Note that the securing screw has a left-hand

thread.

Inserting the keyed chuck (see figure B)

– Clean and lightly grease the insertion end of the shank.

– Insert the keyed chuck with the adapter shank into the

tool holder with a turning motion until it automatically

locks.

– Check that it is locked by pulling the keyed chuck.

Removing the keyed chuck

– Push the locking sleeve (4) back and remove the keyed

chuck (19).

Changing the Tool

The dust protection cap (3) largely prevents the penetration

of drilling dust into the tool holder during operation. When

inserting the tool, make sure that the dust protection cap (3)

does not become damaged.

uReplace a damaged dust protection cap immediately.

It is recommended that you have use an after-sales

service for this.

Changing the tool (SDS plus)

Inserting SDS-plus application tools (seefigureC)

The SDS-plus drill chuck enables you to change the applica-

tion tool easily and conveniently without needing to use ad-

ditional tools.

– Clean and lightly grease the insertion end of the applica-

tion tool.

– Insert the application tool into the tool holder while turn-

ing it until it locks automatically.

– Check the latching by pulling the tool.

As a requirement of the system, the SDS-plus application

tool can move freely. This causes a certain radial run-out at

no-load, which has no effect on the accuracy of the drill hole,

as the drill bit centres itself upon drilling.

Removing SDS-plus application tools (seefigureD)

– Push the locking sleeve (4) back and remove the applica-

tion tool.

Changing the tool (without SDS plus)

Inserting the application tool (seefigureE)

Note: Application tools that do not have SDS plus must not

be used for hammer drilling or chiselling. Tools without SDS

plus and their drill chucks are damaged by hammer drilling

or chiselling.

– Insert a keyed chuck(19).

– Open the keyed chuck(19) by turning it until the tool can

be inserted. Insert the tool.

– Insert the chuck key(21) into the corresponding holes of

the keyed chuck(19) and clamp the tool evenly.

– Turn the impact/mode selector switch(12) to the

"drilling" position.

Removing the application tool (seefigureF)

– Use the chuck key(21) to turn the sleeve of the keyed

chuck(19) anticlockwise until the application tool can be

removed.

Dust/Chip Extraction

The dust from materials such as lead paint, some types of

wood, minerals and metal can be harmful to human health.

Touching or breathing in this dust can trigger allergic reac-

tions and/or cause respiratory illnesses in the user or in

people in the near vicinity.

Certain dusts, such as oak or beech dust, are classified as

carcinogenic, especially in conjunction with wood treatment

additives (chromate, wood preservative). Materials contain-

ing asbestos may only be machined by specialists.

– Use a dust extraction system that is suitable for the ma-

terial wherever possible.

– Provide good ventilation at the workplace.

Bosch Power Tools 1 609 92A 81U | (22.06.2022)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GBH 18V-26 D Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info