Bedienungsanleitung Bosch GBH 18V-28 DC (Seite 23 von 307) (Alle Sprachen)

786123

Zoom out

Zoom in

Vorherige Seite

1/307

Nächste Seite

English | 23

– To deactivate the Bluetooth® Low Energy Module, rotate

the button cell or place means of insulation between the

button cell and Bluetooth® Low Energy Module.

– Close the cover(10) to prevent dirt from getting in.

Practical Advice

uWith the Bluetooth® Low Energy Module GCY 42, the

power tool is equipped with a radio interface. Local

operating restrictions, e.g. in aircraft or hospitals,

must be observed.

uIn areas where the Bluetooth® wireless technology is

not allowed to be used, the Bluetooth® Low Energy

Module GCY42 and the button cell must be removed.

Note: The cover(10) can only be securely closed if the

Bluetooth® Low Energy Module GCY42 and the button cell

are situated in the power tool.

– To deactivate the Bluetooth® Low Energy Module

GCY42, rotate the button cell or place means of insula-

tion between the button cell and Bluetooth® Low Energy

Module GCY42.

– Close the cover(10) to prevent dirt from getting in.

Setting the drilling depth (see figure H)

You can use the depth stop (14) to set the required drilling

depthX.

– Press the button for depth stop adjustment (13) and in-

sert the depth stop into the auxiliary handle (15).

The fluting on the depth stop (14) must face downwards.

– Insert the SDS-plus application tool into the SDS-plus tool

holder (2) to the stop. Otherwise, the movability of the

SDS-plus drilling tool can lead to incorrect adjustment of

the drilling depth.

– Pull the depth stop far enough out that the distance

between the drill bit tip and the edge of the depth stop

corresponds to the required drilling depth X.

Changing the chiselling position (Vario-Lock)

You can lock the chisel in 44 different positions, so you can

select the optimum working position for each task.

– Insert the chisel into the tool holder.

– Turn the impact/mode selector switch (12) to the "Vario-

Lock" position.

– Turn the application tool to the required chisel position.

– Turn the impact/mode selector switch (12) to the "chis-

elling" position. With this, the tool holder is locked.

– Set the rotational direction for chiselling to clockwise.

Inserting screwdriver bits (seefigureI)

uOnly apply the power tool to the screw/nut when the

tool is switched off. Rotating tool inserts can slip off.

A universal holder (22) with SDS-plus shank (accessory) is

required to work with screwdriver bits.

– Clean and lightly grease the insertion end of the shank.

– Insert the universal holder into the tool holder while turn-

ing it until it locks automatically.

– Check that it is locked by pulling the universal holder.

– Insert a screwdriver bit in the universal holder. Only use

screwdriver bits that fit the screw head.

– To remove the universal holder, slide the locking sleeve

(4) backwards and remove the universal holder (22)

from the tool holder.

Hanging up the power tool (seefigureJ)

You can use the utility hook(17) to attach the power tool to

a suitable suspension device.

– Fold the utility hook(17) upwards.

– Check the utility hook(17) for damage or deformation.

Do not use the utility hook(17) if it is damaged, de-

formed or no longer firmly secured to the power tool.

– Use the utility hook(17) to attach the power tool to a sus-

pension device.

To avoid damage or injury, the suspension device must

not be attached above walkways or immediate work

areas.

The utility hook is intended solely for the purpose of

hanging the power tool, including fitted accessories.

– Fold the utility hook(17) in again when you want to begin

work with the power tool.

uNever use the utility hook(17) as a fall protection sys-

tem.

Never attach the fall protection system to the utility

hook.

Attaching the Fall Protection System (seefigureK)

Note: A fall protection system(24) that is suitable for the

weight of the entire system should be used to prevent the

power tool from falling. The maximum permitted length of

the fall protection system is1.8 m. Please always refer to the

permitted attachment area(23) on the power tool.

It is best to use the fall protection system with a tape loop se-

cured by an anchor knot or a fall protection system with fall

damper.

Please always refer to the operating instructions when at-

taching the fall protection system(24).

uAlways secure the opposite side of the fall protection

system to a stable structure (e.g. a building or scaf-

folding) and never to the user.

The fall protection system must be able to move freely

and may only be attached to the power tool at the

fixed anchorage point(25) and in the permitted at-

tachment area(23) .

Select the fixed anchorage point (25) such that the

power tool can fall freely into the fall protection sys-

tem without wrapping around or putting the user at

risk of harm in the event of a fall.

Never use the utility hook(17) as a fall protection sys-

tem.

Never attach the fall protection system to the utility

hook.

Never use the fall protection system on a power tool

which has been fitted with the GDE18V-26D or GDE

16 Plus dust extraction attachments.

Bosch Power Tools 1 609 92A 80W | (05.07.2022)

Bosch GBH 18V-28 DC Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info