Bedienungsanleitung Bosch GBH 18V-34 CF (Seite 24 von 337) (Alle Sprachen)

786259

Zoom out

Zoom in

Vorherige Seite

1/337

Nächste Seite

24 | English

Working mode(25) indic-

ator Functions

lights up Favourite working mode: Individual configuration via smartphone app

The following settings are pre-programmed:

– "Hammer drilling" operating mode (Electronic Precision Control soft start): Fastest pos-

sible run-up up to maximum power

– Rapid Shut-off (KickBack Control) active

– "Chiselling" operating mode (Adaptive Speed Control soft start): Deactivated, fastest pos-

sible run-up up to maximum power

Connectivity functions

In conjunction with the Bluetooth® Low Energy Module

GCY42, the following connectivity functions are available

for the power tool:

– Registration and personalisation

– Status check, output of warning messages

– General information and settings

– Management

Read the corresponding operating instructions for informa-

tion about the Bluetooth® Low Energy ModuleGCY42.

Practical Advice

uWith the Bluetooth® Low Energy Module GCY 42, the

power tool is equipped with a radio interface. Local

operating restrictions, e.g. in aircraft or hospitals,

must be observed.

uIn areas where the Bluetooth® wireless technology is

not allowed to be used, the Bluetooth® Low Energy

Module GCY42 and the button cell must be removed.

Note: The cover(13) can only be securely closed if the

Bluetooth® Low Energy Module GCY42 and the button cell

are situated in the power tool.

– To deactivate the Bluetooth® Low Energy Module

GCY42, rotate the button cell or place means of insula-

tion between the button cell and Bluetooth® Low Energy

Module GCY42.

– Close the cover(13) to prevent dirt from getting in.

Setting the drilling depth (see figure J)

You can use the depth stop (17) to set the required drilling

depthX.

– Press the button for depth stop adjustment (15) and in-

sert the depth stop into the auxiliary handle (16).

The fluting on the depth stop (17) must face downwards.

– Insert the SDS-plus application tool into the SDS-plus tool

holder (3) to the stop. Otherwise, the movability of the

SDS-plus drilling tool can lead to incorrect adjustment of

the drilling depth.

– Pull the depth stop far enough out that the distance

between the drill bit tip and the edge of the depth stop

corresponds to the required drilling depth X.

Overload clutch

uIf the application tool jams or snags, the power trans-

mission to the drill spindle will be interrupted. Always

hold the power tool firmly with both hands to with-

stand the forces this may create and adopt a position

with stable footing.

uSwitch the power tool off immediately and remove the

application tool if the power tool becomes blocked.

Switching on when the drilling tool is blocked may

cause high torque reactions.

Rapid shut-off (KickBack Control)

The rapid shut-off function (KickBack

Control) gives the user greater control

over the power tool and offers them bet-

ter protection than power tools that do

not have Kickback Control. If the power

tool suddenly and unforeseeably rotates

around the drilling axis, it will switch off,

the rapid shut-off indicator (24) will light

up red and the worklight (14) will flash.

When rapid shut-off is activated, the

status indicator(27) flashes red.

– To switch the tool back on, release the on/off switch

(11) and then press it again.

Electronic Precision Control (EPC)

EPC assists you when drilling and when working with impact

in sensitive materials by ensuring slow start-up of the operat-

ing speed for precise working.

Adaptive Speed Control in "Chiselling" Operating Mode

For better control and precise position-

ing, the power tool starts at a low speed

and then increases to the set speed.

Adapted Speed Control is started up

automatically when the power tool is

switched on.

Vibration damping

The integrated vibration damping function re-

duces the generated vibration.

uDo not continue to use the power tool if the damping

element is damaged.

Maintenance and Service

Maintenance and Cleaning

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

1 609 92A 7SJ | (23.06.2022) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GBH 18V-34 CF Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info