Bedienungsanleitung Bosch GBH 2-28 DFV (Seite 4 von 43) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544222

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

4 | English

1 619 92A 067 | (18.10.13) Bosch Power Tools

Service

 Have your power tool serviced by a qualified repair per-

son using only identical replacement parts. This will en-

sure that the safety of the power tool is maintained.

Hammer Safety Warnings

 Wear ear protectors. Exposure to noise can cause hear-

ing loss.

 Use auxiliary handle(s), if supplied with the tool. Loss

of control can cause personal injury.

 Hold power tool by insulated gripping surfaces, when

performing an operation where the cutting accessory

may contact hidden wiring or its own cord. Cutting ac-

cessory contacting a “live” wire may make exposed metal

parts of the power tool “live” and could give the operator an

electric shock.

 When working with the machine, always hold it firmly

with both hands and provide for a secure stance. The

power tool is guided more secure with both hands.

 Secure the workpiece. A workpiece clamped with clamp-

ing devices or in a vice is held more secure than by hand.

Products sold in GB only: Your product is fitted with a

BS 1363/A approved electric plug with internal fuse (ASTA

approved to BS 1362).

If the plug is not suitable for your socket outlets, it should be

cut off and an appropriate plug fitted in its place by an author-

ised customer service agent. The replacement plug should

have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible

shock hazard and should never be inserted into a mains sock-

et elsewhere.

Products sold in AUS and NZ only: Use a residual current de-

vice (RCD) with a rated residual current of 30 mA or less.

Additional Safety and Working In-

structions

 Observe correct mains voltage! The voltage of the pow-

er source must agree with the voltage specified on the

nameplate of the machine. Power tools marked with

230 V can also be operated with 220 V.

 Use appropriate detectors to determine if utility lines

are hidden in the work area or call the local utility com-

pany for assistance. Contact with electric lines can lead

to fire and electric shock. Damaging a gas line can lead to

explosion. Penetrating a water line causes property dam-

age.

 Before any work on the machine itself, pull the mains

plug.

 Firmly tighten the auxiliary handle, hold the machine

firmly with both hands while working and keep proper

footing and balance at all times. The machine is securely

guided with both hands.

 If the application tool should become blocked, switch

the machine off. Loosen the application tool.

 Before switching on the power tool, make sure that the

application tool moves freely. When switching on with a

blocked drilling tool, high torque reaction can occur.

 For drilling without impact in wood, metal, ceramic and

plastic as well as for screwdriving, tools without SDS-plus

are used (e.g., drills with cylindrical shank). For these

tools, a keyless chuck or a key type drill chuck are re-

quired.

 GBH 2-28 DFV: Only use quick change chucks with 3

identification grooves (standard delivery scope) or 2

identification grooves (accessory/spare part) – see

figure 1, page 35.

– The quick change chuck is automatically locked. Check

the locking effect by pulling the quick change chuck.

 Inserting SDS-plus Drilling Tools:

 Check the latching by pulling the tool.

 Replace a damaged dust protection cap immediately.

The dust protection cap largely prevents the penetration of

drilling dust into the tool holder during operation. When in-

serting the tool, pay attention that the dust protection cap

is not damaged.

 Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health and cause allergic reactions, lead to res-

piratory infections and/or cancer. Materials containing

asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suita-

ble for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

 Prevent dust accumulation at the workplace. Dusts can

easily ignite.

 Always wait until the machine has come to a complete

stop before placing it down. The tool insert can jam and

lead to loss of control over the power tool.

OBJ_DOKU-36895-002.fm Page 4 Friday, October 18, 2013 3:55 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GBH 2-28 DFV Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info