Bedienungsanleitung Bosch gbh 24 0 vre (Seite 24 von 282) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

388800

Zoom out

Zoom in

Vorherige Seite

1/282

Nächste Seite

24 | English

1 619 929 740 | (24.7.07) Bosch Power Tools

Reversing the Rotational Direction

f Actuate the rotational direction switch 7

only when the machine is at a standstill.

The rotational direction switch 7 is used to re-

verse the rotational direction of the machine.

However, this is not possible with the On/Off

switch 8 actuated.

Right Rotation: For drilling and driving in

screws, push the rotational direction switch 7

left to the stop.

Left Rotation: For loosening and unscrewing

screws and nuts, press the rotational direction

switch 7 through to the right stop.

Switching On and Off

To start the machine, press the On/Off switch 8

and keep it depressed.

To switch off the machine, release the On/Off

switch 8.

For low temperatures, the machine reaches the

full hammer/impact capacity only after a certain

time.

This start-up time can be shortened by striking

the inserted tool insert against the floor one

time.

Setting the Speed/Impact Rate

The speed/impact rate of the switched on pow-

er tool can be variably adjusted, depending on

how far the On/Off switch 8 is pressed.

Light pressure on the On/Off switch 8 results in

low speed/impact rate. Further pressure on the

switch increases the speed/impact rate.

Run-on Brake

When the On/Off switch 8 is released, the chuck

brakes to a stop, thus preventing the run-on of

the tool.

When driving in screws, wait until the screw is

screwed in flush with the material and then re-

lease the On/Off switch 8. By doing so, the head

of the screw does not penetrate into the materi-

al.

Overload Clutch

f If the tool insert becomes caught or

jammed, the drive to the drill spindle is in-

terrupted. Because of the forces that occur,

always hold the power tool firmly with both

hands and provide for a secure stance.

f If the power tool jams, switch the machine

off and loosen the tool insert. When switch-

ing the machine on with the drilling tool

jammed, high reaction torques can occur.

Operating Instructions

f Do not operate the power tool stationary. It

is not designed for operation in a drill stand.

Inserting Screwdriver Bits (see figure I)

f Apply the power tool to the screw/nut only

when it is switched off. Rotating tool inserts

can slip off.

To work with screwdriver bits, a universal bit

holder 22 with SDS-plus shank (accessory) is re-

quired.

Clean the shank end of the adapter shank and

apply a light coat of grease.

Insert the universal bit holder with a turning mo-

tion into the tool holder until it automatically

locks.

Check the locking effect by pulling the universal

bit holder.

Insert a screwdriver bit into the universal bit

holder. Use only screwdriver bits that match the

screw head.

Set the selector switch 6 to the “Drilling” sym-

bol.

To remove the universal bit holder, pull the lock-

ing sleeve 3 toward the rear and remove the uni-

versal bit holder 22 out of the tool holder.

OBJ_BUCH-372-001.book Page 24 Tuesday, July 24, 2007 1:31 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch gbh 24 0 vre Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info