Bedienungsanleitung Bosch gbh 36 v li compact (Seite 23 von 317) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

388877

Zoom out

Zoom in

Vorherige Seite

1/317

Nächste Seite

English | 23

Bosch Power Tools 1 619 929 797 | (3.2.09)

During the charging procedure, the three green

LEDs light up one after the other and briefly go

out. The battery is fully charged when the three

green LEDs light up continuously. The three

LEDs go out again approx. 5 minutes after the

battery has been fully charged.

The battery is equipped with a NTC temperature

control which allows charging only within a tem-

perature range of between 0 °C and 45 °C. A

long battery service life is achieved in this man-

ner.

Auxiliary Handle

f Operate your machine only with the auxilia-

ry handle 16.

Rotating the Auxiliary Handle (see figure A)

The auxiliary handle 16 can be set to any posi-

tion for a secure and low-fatigue working pos-

ture.

– Turn the wing bolt for adjustment of the aux-

iliary handle 10 in anticlockwise direction

and set the auxiliary handle 16 to the re-

quired position. Then tighten the wing bolt

10 again in clockwise direction.

Adjusting the Drilling Depth (see figure B)

The required drilling depth X can be set with the

depth stop 1.

– Press the button for the depth stop adjust-

ment 9 and insert the depth stop into the

auxiliary handle 16.

The knurled surface of the depth stop 1 must

face downward.

– Insert the SDS-plus drilling tool to the stop

into the SDS-plus tool holder 2. Otherwise,

the movability of the SDS-plus drilling tool

can lead to incorrect adjustment of the drill-

ing depth.

– Pull out the depth stop until the distance be-

tween the tip of the drill bit and the tip of the

depth stop correspond with the desired drill-

ing depth X.

Selecting Drill Chucks and Tools

For hammer drilling, SDS-plus tools are required

that are inserted in the SDS-plus drill chuck.

For drilling without impact in wood, metal, ce-

ramic and plastic as well as for screwdriving,

tools without SDS-plus are used (e.g., drills

with cylindrical shank). For these tools, a key-

less chuck or a key type drill chuck are required.

Changing the Key Type Drill Chuck

To work with tools without SDS-plus (e.g., drills

with cylindrical shank), a suitable drill chuck

must be mounted (key type drill chuck or key-

less chuck, accessories).

Mounting the Key Type Drill Chuck

(see figure C)

– Screw the SDS-plus adapter shank 19 into a

key type drill chuck 18. Secure the key type

drill chuck 18 with the securing screw 17.

Please observe that the securing screw has

a left-hand thread.

Inserting the Key Type Drill Chuck

(see figure D)

– Clean the shank end of the adapter shank

and apply a light coat of grease.

– Insert the key type drill chuck with the adapt-

er shank into the tool holder with a turning

motion until it automatically locks.

– Check the locking effect by pulling the key

type drill chuck.

Removing the Key Type Drill Chuck

– Push the locking sleeve 4 toward the rear

and pull out the key type drill chuck 18.

OBJ_BUCH-518-002.book Page 23 Tuesday, February 3, 2009 12:02 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch gbh 36 v li compact Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info