Bedienungsanleitung Bosch GBH 36 V-LI Plus Professional (Seite 18 von 273) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

591721

Zoom out

Zoom in

Vorherige Seite

1/273

Nächste Seite

18 | English

1 609 92A 0JA | (22.6.15) Bosch Power Tools

Assembly

Battery Charging (see figure A)

 Use only the battery chargers listed on the accessories

page. Only these battery chargers are matched to the lith-

ium-ion battery of your power tool.

Note: The battery supplied is partially charged. To ensure full

capacity of the battery, completely charge the battery in the

battery charger before using your power tool for the first time.

The lithium-ion battery can be charged at any time without re-

ducing its service life. Interrupting the charging procedure

does not damage the battery.

The lithium-ion battery is protected against deep discharging

by the “Electronic Cell Protection (ECP)”. When the battery is

empty, the machine is switched off by means of a protective

circuit: The inserted tool no longer rotates.

 Do not continue to press the On/Off switch after the

machine has been automatically switched off. The bat-

tery can be damaged.

Removing the battery

The battery 11 is equipped with two locking levels that should

prevent the battery from falling out when pushing the battery

unlocking button 18 unintentionally. As long as the battery is

inserted in the power tool, it is held in position by means of a

spring.

To remove the battery 11:

– Push the battery against the base of the power tool (1.)

and at the same time press the battery unlocking button 18

(2.).

– Pull the battery out of the power tool until a red stripe be-

comes visible (3.).

– Press the battery unlocking button 18 again and pull out

the battery completely.

Battery Charge-control Indication

The three green LEDs of the battery charge-control indicator

20 indicate the charge condition of the battery 11. For safety

reasons, it is only possible to check the status of the charge

condition when the machine is at a standstill.

–Push button 21 to indicate the charge condition (also pos-

sible when the battery is removed). The battery charge-

control indicator automatically goes out after approx.

5seconds.

When no LED lights up after pushing button 21, then the bat-

tery is defective and must be replaced.

During the charging procedure, the three green LEDs light up

one after the other and briefly go out. The battery is fully

charged when the three green LEDs light up continuously. The

three LEDs go out again approx. 5 minutes after the battery

has been fully charged.

Auxiliary Handle

 Operate your machine only with the auxiliary handle

16.

Changing the position of the auxiliary handle

(see figure B)

The auxiliary handle 16 can be set to any position for a secure

and low-fatigue working posture.

– Turn the bottom part of the auxiliary handle 16 in counter-

clockwise direction and swivel the auxiliary handle 16 to

the desired position. Then retighten the bottom part of the

auxiliary handle 16 by turning in clockwise direction.

Pay attention that the clamping band of the auxiliary handle is

positioned in the groove on the housing as intended for.

Selecting Drill Chucks and Tools

For hammer drilling and chiselling, SDS-plus tools are re-

quired that are inserted in the SDS-plus drill chuck.

For drilling without impact in wood, metal, ceramic and plas-

tic as well as for screwdriving, tools without SDS-plus are

used (e.g., drill bits with cylindrical shank). For these tools, a

keyless chuck or a key type drill chuck are required.

Inserting/Removing the Key Type Drill Chuck

(GBH 36 V-LI Plus)

To work with tools without SDS-plus (e.g., drills with cylindri-

cal shank), a suitable drill chuck must be mounted (key type

drill chuck or keyless chuck, accessories).

Mounting the Key Type Drill Chuck (see figure C)

– Screw the SDS-plus adapter shank 24 into a key type drill

chuck 23. Secure the key type drill chuck 23 with the se-

curing screw 22. Please observe that the securing

screw has a left-hand thread.

Inserting the Key Type Drill Chuck (see figure C)

– Clean the shank end of the adapter shank and apply a light

coat of grease.

– Insert the key type drill chuck with the adapter shank into

the tool holder with a turning motion until it automatically

locks.

– Check the locking effect by pulling the key type drill chuck.

LED Capacity

Continuous lighting 3 x green ≥ 2/3

Continuous lighting 2 x green ≥ 1/3

Continuous lighting 1 x green <1/3

Flashing light 1 x green Reserve

OBJ_BUCH-283-012.book Page 18 Monday, June 22, 2015 10:28 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GBH 36 V-LI Plus Professional Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info