Bedienungsanleitung Bosch GBH 36 V-LI Plus Professional (Seite 21 von 273) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

591721

Zoom out

Zoom in

Vorherige Seite

1/273

Nächste Seite

English | 21

Bosch Power Tools 1 609 92A 0JA | (22.6.15)

Temperature Control Indicator

The red LED of the temperature control indicator 19 signals

that the battery or the electronics of the power tool (when the

battery is inserted) are not within the optimum temperature

range. In this case, the power tool will not operate at full ca-

pacity.

Temperature control of the battery:

–The red LED 19 lights up continuously after inserting the

battery into the charger: The battery is not within the

charging temperature range between 0 °C and 45 °C and

cannot be charged.

–The red LED 19 flashes when you press the 21 button or

the On/Off switch 10 (with battery inserted): The battery

is outside of the permitted operating temperature range.

– For battery temperatures over 70 °C, the power tool

switches off until the battery is in the optimal temperature

range again.

Temperature control of the power tool electronics:

–The red LED 19 lights up continuously when pressing the

On/Off switch 10: The temperature of the machine’s elec-

tronics is below 5 °C or above 75 °C.

– At a temperature above 90 °C , the electronics of the pow-

er tool switch off until the temperature is within the allow-

able temperature range again.

Working Advice

Adjusting the Drilling Depth (see figure M)

The required drilling depth X can be set with the depth stop

17.

– Press the button for the depth stop adjustment 15 and in-

sert the depth stop into the auxiliary handle 16.

The knurled surface of the depth stop 17 must face down-

ward.

– Insert the SDS-plus drilling tool to the stop into the SDS-

plus tool holder 3. Otherwise, the movability of the SDS-

plus drilling tool can lead to incorrect adjustment of the

drilling depth.

– Pull out the depth stop until the distance between the tip of

the drill bit and the tip of the depth stop corresponds with

the desired drilling depth X.

Changing the Chiselling Position (Vario-Lock)

The chisel can be locked in 36 positions. In this manner, the

optimum working position can be set for each application.

– Insert the chisel into the tool holder.

– Turn the mode selector switch 13 to the “Vario-Lock” posi-

tion (see “Setting the operating mode”, page 20).

– Turn the tool holder to the desired chiselling position.

– Turn the mode selector switch 13 to the “chiselling” posi-

tion. The tool holder is now locked.

– For chiselling, set the rotation direction to right rotation.

Inserting Screwdriver Bits (see figure N)

 Apply the power tool to the screw/nut only when it is

switched off. Rotating tool inserts can slip off.

To work with screwdriver bits, a universal bit holder 31 with

SDS-plus shank (accessory) is required.

– Clean the shank end of the adapter shank and apply a light

coat of grease.

– Insert the universal bit holder with a turning motion into

the tool holder until it automatically locks.

– Check the locking effect by pulling the universal bit holder.

– Insert a screwdriver bit into the universal bit holder. Use

only screwdriver bits that match the screw head.

– To remove the universal bit holder, pull the locking sleeve

5 toward the rear and remove the universal bit holder 31

out of the tool holder.

Vibration Damper

The integrated vibration damper reduces occurring vibra-

tions.

The soft grip handle increases the safety against slipping off

and thus provides for a better grip and handling of the power

tool.

Recommendations for Optimal Handling of the Battery

Protect the battery against moisture and water.

Store the battery only within a temperature range between

–20 °C and 50 °C. As an example, do not leave the battery in

the car in summer.

Occasionally clean the venting slots of the battery using a soft,

clean and dry brush.

A significantly reduced working period after charging indi-

cates that the battery is used and must be replaced.

Observe the notes for disposal.

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine itself (e. g. mainte-

nance, tool change, etc.) as well as during transport

and storage, remove the battery from the power tool.

There is danger of injury when unintentionally actuating

the On/Off switch.

 For safe and proper working, always keep the machine

and ventilation slots clean.

 A damaged dust protection cap should be changed im-

mediately. We recommend having this carried out by

an after-sales service.

– Clean the tool holder 3 each time after using.

After-sales Service and Application Service

Our after-sales service responds to your questions concern-

ing maintenance and repair of your product as well as spare

parts. Exploded views and information on spare parts can al-

so be found under:

www.bosch-pt.com

Bosch’s application service team will gladly answer questions

concerning our products and their accessories.

OBJ_BUCH-283-012.book Page 21 Monday, June 22, 2015 10:28 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GBH 36 V-LI Plus Professional Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info