Bedienungsanleitung Bosch GBM 16-2 RE Professional (Seite 13 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

591840

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

English | 13

Bosch Power Tools 1 609 929 T41 | (24.10.11)

Declaration of Conformity

We declare under our sole responsibility that the product de-

scribed under “Technical Data” is in conformity with the fol-

lowing standards or standardization documents: EN 60745

according to the provisions of the directives 2011/65/EU,

2004/108/EC, 2006/42/EC.

Technical file (2006/42/EC) at:

Robert Bosch GmbH, PT/ETM9,

D-70745 Leinfelden-Echterdingen

Robert Bosch GmbH, Power Tools Division

D-70745 Leinfelden-Echterdingen

05.10.2011

Assembly

f Before any work on the machine itself, pull the mains

plug.

Auxiliary Handle (see figure A)

f Operate your machine only with the auxiliary handle 9.

The auxiliary handle 9 can be set to any position for a secure

and low-fatigue working posture.

Turn the bottom part of the auxiliary handle 9 in counterclock-

wise direction and swivel the auxiliary handle 9 to the desired

position. Then retighten the bottom part of the auxiliary han-

dle 9 by turning in clockwise direction.

Adjusting the Drilling Depth

The required drilling depth X can be set with the depth stop 7.

Loosen the wing bolt for the depth stop adjustment 8 and in-

sert the depth stop rod into the auxiliary handle 9.

Pull out the depth stop until the distance between the tip of

the drill bit and the tip of the depth stop correspond with the

desired drilling depth X.

Changing the Tool (see figure B)

f Wear protective gloves when changing the tool. The drill

chuck can become very hot during longer work periods.

Open the key type drill chuck 1 by turning until the tool can be

inserted. Insert the tool.

Insert the chuck key 5 into the corresponding holes of the key

type drill chuck 1 and clamp the tool uniformly.

Replacing the Drill Chuck (see figure C)

To dismount the key type drill chuck 1 position an open-end

spanner (size 27 mm) against the nut on the drive spindle. Firm-

ly hold the key type drill chuck with one hand and with the other

hand, turn the open-end spanner in anticlockwise direction until

the drill chuck is released from the tapered drill spindle.

f Keep the drill spindle taper and the drill hole of the drill

chuck free from grease and debris.

To mount the key type drill chuck 1 turn the nut on the drive

spindle in clockwise direction to the stop. Place the key type

drill chuck without force onto the drive spindle until it is tightly

seated. Apply light blows with a rubber hammer onto the face

side of the key type drill chuck 1 to ensure tight seating of the

chuck. Pay attention that the clamping jaws of the key type

drill chuck do not project, in order not to damage them.

Dust/Chip Extraction

f Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

f Prevent dust accumulation at the workplace. Dusts can

easily ignite.

Operation

Starting Operation

f Observe correct mains voltage! The voltage of the pow-

er source must agree with the voltage specified on the

nameplate of the machine. Power tools marked with

230 V can also be operated with 220 V.

Reversing the Rotational Direction

The rotational direction switch 6 is used to reverse the rota-

tional direction of the machine. However, this is not possible

with the On/Off switch 4 actuated.

Right rotation: For drilling and screwdriving, press the rota-

tional direction switch 6 downward to “R”.

Left rotation: For loosening and unscrewing screws and

nuts, press the rotational direction switch 6 upward to “L”.

Gear Selection, Mechanical

f Actuate the gear selector 2 only when the machine is at

a standstill.

Two speed ranges can be preselected with the gear selector 2.

1st gear:

Low speed range; for working with large drill-

ing diameter.

2nd gear:

Higher speed range; for working with small

drilling diameter.

If the gear selector 2 cannot be fully engaged, lightly rotate

the drive spindle with the drill bit by twisting the drill chuck.

Dr. Egbert Schneider

Senior Vice President

Engineering

Dr. Eckerhard Strötgen

Engineering Director

PT/ESI

OBJ_BUCH-21-005.book Page 13 Monday, October 24, 2011 10:57 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GBM 16-2 RE Professional Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch GBM 16-2 RE Professional

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info