Bedienungsanleitung Bosch gbs 75 ae - set (Seite 18 von 202) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

389406

Zoom out

Zoom in

Vorherige Seite

1/202

Nächste Seite

18 | English

2 609 932 674 | (27.2.09) Bosch Power Tools

Integrated Dust Extraction with Dust Bag

For small sanding jobs, a dust bag 7 (accessory)

can be connected. Attach the sleeve of the dust

bag firmly onto the outlet piece 9. To maintain

optimum dust collection, empty the dust bag 7

in good time.

Changing the Sanding Belt

(see figure A)

– Completely pivot out the clamping lever 3.

The sanding belt 2 is now loose and can be

removed.

– Mount the new sanding belt 2. Pay attention

that the direction of the arrows on the inside

of the sanding belt correspond with the ar-

row direction on the machine housing.

– Pivot the clamping lever 3 back to its initial

position.

– Pick up the power tool and switch it on. Ad-

just the belt run with adjustment knob 8 until

the edge of the sanding belt runs flush with

the guide plate 13.

Pay attention that the sanding belt 2 does not

move excessively and make contact with the

housing. Check the belt run regularly and read-

just with the adjusment knob 8.

Selecting the Sanding Belt

Depending on the material to be worked and the

required rate of removal, different sanding belts

are available:

Operation

Starting Operation

f Observe correct mains voltage! The voltage

of the power source must agree with the

voltage specified on the nameplate of the

machine. Power tools marked with 230 V

can also be operated with 220 V.

Switching On and Off

To start the machine, press the On/Off switch 5

and keep it pressed.

To lock the pressed On/Off switch 5, press the

lock-on button 6.

To switch off the machine, release the On/Off

switch 5 or when it is locked with the lock-on

button 6, briefly press the On/Off switch 5 and

then release it.

Preselecting the Belt Speed

The necessary belt speed can be preselected

with the thumbwheel 4, even during operation.

The required belt speed depends on the materi-

al being sanded and on the working conditions,

and can be determined by practical testing.

Working Advice

The sanding removal rate and the surface quality

are mainly determined by the selection of the

sanding belt as well as by the preselected belt

speed. The higher the belt speed, the more ma-

terial is removed and the finer the sanded sur-

face.

Only flawless sanding belts achieve good sand-

ing capacity and make the machine last longer.

Work using the least possible sanding pressure

in order to increase the service life of the sand-

ing belts. The machine’s own weight is sufficient

for a good sanding performance. An excessive

increase of the sanding pressure does not lead

to an increase of the sanding capacity, but to in-

creased wear of the machine and the sanding

belt.

Grain size

For the working of all

wooden materials

40—240

For coarse-sanding,

e. g. of rough,

unplaned beams and

boards coarse 40, 60

For face sanding and

planing small irregu-

larities medium 80, 100, 120

For finish and fine

sanding of hard

woods fine 180, 240

OBJ_BUCH-459-002.book Page 18 Friday, February 27, 2009 11:03 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch gbs 75 ae - set Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info