594618

Bosch GCM 12 SDE Professional Seite 34

34
Zoom out
Zoom in
Vorherige Seite
1/402
Nächste Seite
34 | English
1 609 92A 0Z5 | (22.12.14) Bosch Power Tools
Operation
Before any work on the machine itself, pull the mains
plug.
Transport Safety (see figure E)
The transport safety-lock 9 enables easier handling of the ma-
chine when transporting to various working locations.
Releasing the Machine (Working Position)
– Push the tool arm by the handle 12 down a little in order to
relieve the transport safety-lock 9.
– Pull the transport safety-lock 9 completely outward.
– Guide the tool arm slowly upward.
Securing the Machine (Transport Position)
– Loosen the locking screw 6 if tightened. Pull the tool arm
completely to the front and tighten the locking screw
again.
– Screw adjusting screw 40 completely upward.
– To lock the saw table 19, tighten the locking knob 22.
– Push the locking lever 13 and guide the tool arm slowly
downward with the tool handle 12.
– Guide the tool arm downward until the transport safety-
lock 9 can be pushed completely inward.
Preparing for Operation
Extending the Saw Table (see figure F)
Long workpieces must be underlaid or supported at their free
end.
The saw table can be extended left and right with the saw-ta-
ble extensions 28.
– Loosen the clamping screw 17.
– Pull out the saw-table extension 28 to the desired length.
– Retighten the clamping screw 17 to fix the saw-table ex-
tension.
Moving the Fence (see figure G)
When sawing vertical bevel angles, you have to pull the left-
hand or right-hand adjustable fence 2 outward depending on
the cutting direction, or remove it completely.
Clamping the Workpiece (see figure H)
To ensure optimum working safety, the workpiece must al-
ways be firmly clamped.
Do not saw workpieces that are too small to clamp.
– Press the workpiece firmly against the fences 2 and 1.
– Insert the material clamp 39 provided into one of the holes
30 intended for it.
– Loosen the wing bolt 51 and adapt the material clamp to
the workpiece. Tighten the wing bolt again.
– Firmly tighten the threaded rod 50, thus fastening the
workpiece.
Adjusting Mitre Angles
To ensure precise cuts, the basic adjustment of the machine
must be checked and adjusted as necessary after intensive
use (see “Checking and Adjusting the Basic Adjustment”,
page 36).
Adjusting Standard Mitre Angles (see figure I1)
For quick and precise adjustment of commonly used mitre an-
gles, detents 26 have been provided for on the saw table:
– Loosen the locking knob 22 in case it is tightened.
– Pull lever 23 and rotate the saw table 19 left or right to the
requested detent.
– Release the lever again. The lever must be felt to engage in
the detent.
Adjusting Any Mitre Angle (see figure I2)
The mitre angle can be set in the range from 52° (left side) to
60° (right side).
– Loosen the locking knob 22 in case it is tightened.
– Pull lever 23 and at the same time push the locking bracket
21 until it engages in the groove intended for this. The saw
table can be moved freely now.
– Turn the saw table 19 left or right by the locking knob until
the angle indicator 25 indicates the requested mitre angle.
For mitre angles greater than 45°:
Pull the saw-table extension 28 completely outward (see
“Extending the Saw Table”, page 34).
– Tighten the locking knob 22 again.
– To loosen the lever 23 again (for adjusting standard mitre
angles), pull the lever upward.
The locking bracket 21 snaps back to its original position
and lever 23 can re-engage into the detents 26.
Adjusting Bevel Angles
To ensure precise cuts, the basic adjustment of the machine
must be checked and adjusted as necessary after intensive
use (see “Checking and Adjusting the Basic Adjustment”,
page 36).
The vertical bevel angle can be adjusted in a range from 47°
(leftward) to 47° (rightward).
For quick and precise setting of frequently used bevel angles,
stops have been provided for the angles 0°, 47°, 45°, 33.9°
and 22.5°.
With vertical mitre cuts and the use of the SDS bolt 31,
you need to ensure that the SDS bolt can never come in-
to contact with the workpiece surface before sawing.
This is done by setting an appropriate depth stop (see
“Adjusting the Depth Stop”, page 36). This prevents,
that the SDS bolt and / or the workpiece may be damaged.
Bevel angle range
–2°... 40° leftward – Loosen the locking screw 37.
– Pull the adjustable fence 2 com-
pletely outward.
–2°... 35° rightward
>40° leftward – Loosen the locking screw 37.
– Pull the adjustable fence 2 com-
pletely outward.
– Remove the adjustable fence
upward.
>35° rightward
Left Right
0°
15°; 22.5°;
31.6°; 45°
15°; 22.5°;
31.6°; 45°; 60°
OBJ_BUCH-2301-002.book Page 34 Monday, December 22, 2014 10:15 AM
… 34 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch GCM 12 SDE Professional wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info