Bedienungsanleitung Bosch GCM 12 SDE Professional (Seite 38 von 402) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

594618

Zoom out

Zoom in

Vorherige Seite

1/402

Nächste Seite

38 | English

1 609 92A 0Z5 | (22.12.14) Bosch Power Tools

Adjusting: (see figureU2)

– Loosen the lock nut of the stop screw 63 using a conven-

tional ring spanner or open-end spanner (10 mm).

– Screw the stop screw in or out until the leg of the angle

gauge is flush with the saw blade over the complete length.

–Tighten clamping lever 7 again.

– Then retighten the lock nut of the stop screw 63.

When the angle indicators 43 and 5 are not in line with the 45 °

marks of scale 4 after adjusting, firstly once more check the

0° setting for the bevel angle and the angle indicators. Then

repeat the adjustment of the 45° bevel angle.

Setting the Standard 45° Bevel Angle (Rightward)

– Bring the power tool into the working position.

– Turn the saw table 19 to the 0° detent 26. The lever 23

must be felt to engage in the detent.

– Remove the right-hand adjustable fence 2 (see “Moving

the Fence”, page 34).

– Pull the stop 44 completely forward.

– Turn the right-hand stop 3 until the standard 45° bevel an-

gle engages at the arrow mark.

– Loosen clamping lever 7.

– Swing the tool arm to the right by the handle 12 until the

stop screw 64 rests on the stop 3.

Checking: (see figure V1)

– Set an angle gauge to 135° and place it on the saw table

The leg of the angle gauge must be flush with the saw blade 48

over the complete length.

Adjusting: (see figureV2)

– Loosen the lock nut of the stop screw 64 using a conven-

tional ring spanner or open-end spanner (10 mm).

– Screw the stop screw in or out until the leg of the angle

gauge is flush with the saw blade over the complete length.

–Tighten clamping lever 7 again.

– Then retighten the lock nut of the stop screw 64.

When the angle indicators 43 and 5 are not in line with the 45 °

marks of scale 4 after adjusting, firstly once more check the

0° setting for the bevel angle and the angle indicators. Then

repeat the adjustment of the 45° bevel angle.

Aligning the Scale for Mitre Angles

– Bring the power tool into the working position.

– Turn the saw table 19 to the 0° detent 26. The lever 23

must be felt to engage in the detent.

Checking: (see figure W1)

– Adjust an angle gauge to 90° and position it between the

fence 1 and the saw blade 48 on the saw table 19.

The leg of the angle gauge must be flush with the saw blade 48

over the complete length.

Adjusting: (see figureW2)

– Loosen all four set screws 65 with the hex key (4 mm) 38

and turn the saw table 19 together with the scale 27 until

the leg of the angle gauge is flush with the saw blade over

the complete length.

– Retighten the screws again.

When the angle indicator 25 is not in line with the 0° mark of

scale 27 after adjusting, loosen screw 66 with a cross-head

screwdriver and align the angle indicator alongside the

0°mark.

Transport (see figure X)

Before transporting the power tool, the following steps must

be carried out:

– Loosen the locking screw 6 if tightened. Pull the tool arm

completely to the front and tighten the locking screw

again.

– Make sure that the depth stop 41 is swung completely

backward and that the adjusting screw 40 fits through the

recess without touching the depth stop when moving the

tool arm.

– Bring the machine into the transport position.

– Remove all accessories that cannot be mounted firmly to

the power tool.

If possible, place unused saw blades in an enclosed con-

tainer for transport.

– Wind up the mains cable and tie it together with Velcro

strap 67.

– Carry the machine by the transport handle 10 or hold it by

the recessed handles 29 on the sides of the saw table.

 The power tool should always be carried by two per-

sons in order to avoid back injuries.

 When transporting the power tool, use only the trans-

port devices and never use the protective devices.

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine itself, pull the mains

plug.

If the replacement of the supply cord is necessary, this has to

be done by Bosch or an authorized Bosch service agent in or-

der to avoid a safety hazard.

Cleaning

For safe and proper working, always keep the power tool and

its ventilation slots clean.

The retracting blade guard must always be able to move freely

and retract automatically. Therefore, always keep the area

around the retracting blade guard clean.

Remove dust and chips after each working procedure by

blowing out with compressed air or with a brush.

Clean the roller 16 regularly.

Measures for Noise Reduction

Measures on behalf of the manufacturer:

–Soft starting

– Delivery of the machine with a saw blade developed partic-

ularly for noise reduction

Measures on behalf of the user:

– Low-vibration assembly on a firm working surface

– Use of saw blades with noise-reducing functions

– Regular cleaning of saw blade and power tool

OBJ_BUCH-2301-002.book Page 38 Monday, December 22, 2014 10:15 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GCM 12 SDE Professional Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info