Bedienungsanleitung Bosch GCM 350-254 (Seite 41 von 475) (Alle Sprachen)

786479

Zoom out

Zoom in

Vorherige Seite

1/475

Nächste Seite

English | 41

Checking (see figure T1)

– Set an angle gauge to 90° and place it on the saw table

(18).

The leg of the angle gauge must be flush with the saw blade

(47) along its entire length.

Setting (see figure T2)

– Loosen the clamping lever (7).

– Swing the stop(42) all the way in.

– Loosen the lock nut of the stop screw(65) with a com-

mercially available ring or open-ended spanner (10mm).

– Turn the stop screw as far in or out as needed until the leg

of the angle gauge is flush with the saw blade along its en-

tire length.

– Re-tighten the clamping lever (7).

– Then re-tighten the lock nut of the stop screw (65).

If the angle indicators (41) and (5) are not in line with the 0°

marks on the scale (4) following adjustment, loosen the

fastening screws on the angle indicators using a cross-

headed screwdriver and align the angle indicators with the

0° marks.

Setting the Standard 45° Mitre Angle (left)

– Bring the power tool into the work position.

– Turn the saw table(18) to the 0° detent(25). The

lever(22) must be felt to engage in the detent.

– Remove the left-hand adjustable fence(2)

– Turn the left-hand stop(3) until the standard 45° mitre

angle engages at the arrow mark.

– Loosen the clamping lever(7).

– Swivel the tool arm by the handle(12) to the left until the

stop screw(66) rests on the stop(3).

Checking (see figure U1)

– Set an angle gauge to 45° and place it on the saw table

(18).

The leg of the angle gauge must be flush with the saw blade

(47) along its entire length.

Setting (see figureU2)

– Loosen the lock nut of the stop screw(66) using a com-

mercially available box-ended or open-ended spanner

(size10mm).

– Turn the stop screw(66) as far in or out as needed until

the leg of the angle gauge is flush with the saw blade along

its entire length.

– Retighten the clamping lever(7).

– Then retighten the lock nut of the stop screw(66).

If the angle indicators(41) and(5) are not in line with the

45° marks on the scale(4) following adjustment, first check

the 0° setting for the bevel angle and the angle indicators

once more. Then repeat the adjustment of the 45° bevel

angle.

Setting the Standard 45° Mitre Angle (right)

– Bring the power tool into the work position.

– Turn the saw table (18) to the 0° detent (25). The lever

(22) must be felt to engage in the detent.

– Remove the right adjustable fence(2).

– Swing the stop(42) all the way out

– Turn the right stop(3) until the standard 45° bevel angle

engages at the arrow mark.

– Loosen the clamping lever(7).

– Swing the tool arm left by the handle(12) until the stop

screw(67) lies on the stop(3).

Checking (see figure V1)

– Set an angle gauge to 135° and place it on the saw table

(18).

The leg of the angle gauge must be flush with the saw blade

(47) along its entire length.

Setting (see figure V2)

– Loosen the lock nut of the stop screw(67) with a com-

mercially available ring or open-ended spanner (10mm).

– Turn the stop screw(67) as far in or out as needed until

the leg of the angle gauge is flush with the saw blade along

its entire length.

– Re-tighten the clamping lever (7).

– Then re-tighten the lock nut of the stop screw(67).

If the angle indicators (41) and (5) are not in line with the

45° marks on the scale (4) following adjustment, first check

the 0° setting for the bevel angle and the angle indicators

once more. Then repeat the adjustment of the 45° bevel

angle.

Aligning the scale for mitre angles

– Bring the power tool into the work position.

– Turn the saw table (18) to the 0° detent (25). The lever

(22) must be felt to engage in the detent.

Checking (see figure W1)

– Set an angle gauge to 90° and position it between the

fence (1) and the saw blade (47) on the saw table (18).

The leg of the angle gauge must be flush with the saw blade

(47) along its entire length.

Setting (see figure W2)

– Loosen all four set screws (68) using the hex key (4mm)

(37) and turn the saw table (18) together with the scale

(26) until the leg of the angle gauge is flush with the saw

blade along its entire length.

– Re-tighten the screws again.

If the angle indicator (24) is not aligned with the 0° mark on

the scale (26) following adjustment, loosen the screw (69)

using a cross-headed screwdriver and align the angle indic-

ator along the 0° mark.

Transport (see figureX)

Before transporting the power tool, the following steps must

be carried out:

– Loosen the locking screw(6) if it is tightened. Pull the

tool arm fully forwards and retighten the locking screw.

– Ensure that the depth stop(40) is swung all the way back

and the adjusting screw(39) fits through the recess

without touching the depth stop when you move the tool

arm.

– Push the saw table extensions all the way in and fix them

there.

Bosch Power Tools 1 609 92A 7N9 | (26.04.2022)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GCM 350-254 Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info