Bedienungsanleitung Bosch GCM 8000 SJ Professional (Seite 25 von 298) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

594598

Zoom out

Zoom in

Vorherige Seite

1/298

Nächste Seite

English | 25

Bosch Power Tools 1 609 92A 0HN | (16.6.14)

Position of the Operator (see figure K)

 Do not stand in a line with the saw blade in front of the

machine. Always stand aside of the saw blade. This pro-

tects your body against possible kickback.

– Keep hands, fingers and arms away from the rotating saw

blade.

– Do not cross your arms when operating the tool arm.

Permissible Workpiece Dimensions

Maximal workpiece sizes:

Minimal workpiece sizes (= all workpieces that can be

clamped left or right from the saw blade with the supplied ma-

terial clamp 5):100 x 40 mm (length x width)

Cutting depth, max. (0°/0°): 70 mm

Replacing Insert Plates (see figure L)

The red insert plates 21 can become worn after prolonged

use of the machine.

Replace defective insert plates.

– Bring the power tool into the working position.

–Unscrew the screws 44 with a hex key (size 4 mm) and re-

move the old insert plates.

– Insert the new right-hand insert plate.

– Screw the insert plate as far as possible to the right with

the screws 44 so that the saw blade does not come into

contact with the insert plate over the complete length of

the possible slide motion.

– Repeat the work steps in the same manner for the left-hand

insert plate.

Sawing

 Always tighten the locking knob 23 firmly before saw-

ing. Otherwise the saw blade can become wedged in the

workpiece.

Sawing without Slide Movement (Cutting Off)

(see figure M)

– For cuts without slide movement (small workpieces), loos-

en the locking screw 9 if it is tightened. Push the tool arm

all the way towards the fences 4 and 19 and retighten the

locking screw 9.

– Set the desired mitre angle.

– Press the workpiece firmly against the fences 4 and 19.

– Firmly clamp the workpiece as appropriate for its dimen-

sions.

– Switch on the machine.

– Press locking switch 15 and slowly guide the tool arm

downward by the handle 14.

– Saw through the workpiece applying uniform feed.

– Switch off the machine and wait until the saw blade has

come to a complete stop.

– Guide the tool arm slowly upward.

Sawing with Slide Movement

– For cuts using the slide device 10 (wide workpieces), loos-

en the locking screw 9 in case it is tightened.

– Set the desired mitre angle.

– Press the workpiece firmly against the fences 4 and 19.

– Firmly clamp the workpiece as appropriate for its dimen-

sions.

– Pull the tool arm away from the fences 4 and 19 until the

saw blade is in front of the workpiece.

– Switch on the machine.

– Press locking switch 15 and slowly guide the tool arm

downward by the handle 14.

– Now push the tool arm toward the fences 4 and 19 and saw

through the workpiece with uniform feed.

– Switch off the machine and wait until the saw blade has

come to a complete stop.

– Guide the tool arm slowly upward.

Special Workpieces

When sawing curved or round workpieces, these must be es-

pecially secured against slipping. At the cutting line, no gap

may exist between workpiece, fence and saw table.

Provide for special fixtures, if required.

Checking and Adjusting the Basic Adjustment

 Before any work on the machine itself, pull the mains

plug.

To ensure precise cuts, the basic adjustment of the machine

must be checked and adjusted as necessary after intensive

use.

A certain level of experience and appropriate specialty tools

are required for this.

A Bosch after-sales service station will handle this mainte-

nance task quickly and reliably.

Setting the Standard Bevel Angle 0° (Vertical)

– Bring the power tool into the working position.

– Turn the saw table 20 to the 0° detent 26. The lever 24

must be felt to engage in the detent.

Checking: (see figure N1)

– Adjust an angle gauge to 90° and position it on the saw ta-

ble 20.

The leg of the angle gauge must be flush with the saw blade 38

over the complete length.

Adjusting: (see figureN2)

– Loosen the lock nut of the stop screw 31 using a commer-

cial box-end or open-end spanner (size 10 mm).

– Screw the stop screw in or out until the leg of the angle

gauge is flush with the saw blade over the complete length.

– Retighten the lock lever 8 again.

– Afterwards, retighten the lock nut of the stop screw 31

again.

In case the angle indicator 30 is not in a line with the 0° mark

of the scale 29 after the adjustment, loosen the screw 45 us-

ing a commercial cross-head screwdriver and align the angle

indicator along the 0° mark.

Mitre/Bevel Angle Height x Width [mm]

Horizontal Vertical

0° 0°

70 x 270

45° 0°

70 x 190

0° 45°

45 x 270

OBJ_BUCH-2154-002.book Page 25 Monday, June 16, 2014 2:55 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GCM 8000 SJ Professional Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info