Bedienungsanleitung Bosch GDB 350 WE Professional (Seite 13 von 177) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

591910

Zoom out

Zoom in

Vorherige Seite

1/177

Nächste Seite

English | 13

Bosch Power Tools 1 609 92A 1A4 | (12.5.15)

If the red control indicator does not extinguish when you

press the “TEST” button or if it extinguishes repeatedly when

the power tool is switched on, then you must have the power

tool checked by an authorised Bosch after-sales service

agent.

 If the portable residual current device (PRCD) is defec-

tive, the power tool must not be operated.

Switching On

Press the “RESET” button on the portable residual current

device (PRCD) 2.

Set the water cock 8 to flow.

To switch on the machine, flip the On/Off switch 3 to

position I.

To save energy, only switch the power tool on when using it.

Switching Off

To switch off the machine, flip the On/Off switch 3 to position

Shut the water cock 8. After finishing work, disconnect the

water outlet connector 7 from the water supply. Open the wa-

ter cock 8 and drain the remaining water.

Reduced starting current

The electronics of the power tool make the motor start softly,

therefore preventing the starting current from being too high.

Restarting Protection

The restarting protection feature prevents uncontrolled

restarting of the machine after an interruption in the power

supply.

To restart, press the “RESET” button on the portable residu-

al current device (PRCD) 2. Then switch the On/Off switch 3

to the off-position and switch the power tool on again.

Preselecting the Speed

Three speeds can be preselected using the gear selector 6.

The gears are recommended for the following drilling diame-

ters:

Working Advice

 Before any work on the machine itself, pull the mains

plug.

Loosen the parking brake 5 in order to drill. When doing so,

hold the star handle 4 of the drill stand in place in order to pre-

vent the drill from sliding down in an uncontrolled manner

(see operating instructions of the drill stand).

Start drilling in 1st gear with low speed until the core bit ro-

tates in the material without vibrating. Then switch to 2nd or

3rd gear if necessary.

While drilling, adapt the feed pressure to the material being

drilled. Drill with uniform pressure. Lightly pull the core bit

out of the bore from time to time so that the drilling sludge is

removed from the core bit segments.

Overload Clutch

If a core bit jams or snags, the drive to the drill spindle will be

interrupted. In this case, switch the power tool off immediate-

ly to prevent wear and heat build-up.

Dislodge the core bit by turning it to the right and left using a

suitable open-end spanner. Carefully pull the power tool out

of the bore hole as you do so.

Overload Protection

If the overload threshold is exceeded, then the power tool will

begin to pulsate noticeably. Reduce the feed pressure until

the power tool works normally again.

If the feed pressure is not reduced, then the power tool will

switch off. You can then switch the power tool back on

straightaway, but you should continue to work with reduced

feed pressure.

Removing the Core

After drilling, continue to run the water for a short period in or-

der to flush out the drilling sludge between the core bit and

the core.

If the drilling core is stuck in the core bit, then apply light

blows onto the core bit with a piece of soft wood or plastic in

order to loosen the core. If required, pry the drilling core out

of the core bit using an appropriate hand tool (slotted screw-

driver or similar).

Note: Do not hammer or apply blows onto the core bit with

hard objects (danger of deformation)!

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine itself, pull the mains

plug.

 For safe and proper working, always keep the machine

and ventilation slots clean.

Clean the drilling spindle 10 after finishing work. Occasionally

spray an anti-corrosion agent onto the drilling spindle and the

core bit 9.

If the replacement of the supply cord is necessary, this has to

be done by Bosch or an authorized Bosch service agent in or-

der to avoid a safety hazard.

1st gear 165–350 mm

2nd gear 80–160 mm

3rd gear 55–105 mm

OBJ_BUCH-2203-002.book Page 13 Tuesday, May 12, 2015 9:22 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GDB 350 WE Professional Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info