Bedienungsanleitung Bosch GDC 125 Professional (Seite 17 von 221) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

594764

Zoom out

Zoom in

Vorherige Seite

1/221

Nächste Seite

English | 17

Bosch Power Tools 1 609 92A 0Y3 | (4.2.15)

Dust Extraction

Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the mate-

rials to be worked.

Prevent dust accumulation at the workplace. Dusts can

easily ignite.

Mounting/Replacing the Diamond Cutting Disc

(see figure A)

When mounting and replacing diamond cutting discs, it

is recommended to wear protective gloves.

Diamond cutting discs become very hot during opera-

tion; do not touch them until they have cooled down.

Always use a correctly sized diamond cutting disc with

the fitting mounting hole that corresponds with the in-

formation listed in the technical data.

Use only diamond-tipped cutting discs. Segmented dia-

mond wheels may only have negative cutting angles

and slots between the segments to a maximum of

10 mm.

Mounting the Diamond Cutting Disc

– Clean the diamond cutting disc 19 and all clamping parts

to be mounted.

– Mount the mounting flange 18 onto the drive spindle 17.

– Place the diamond cutting disc 19 onto the mounting

flange 18. The direction arrow on the diamond cutting disc

19 and the direction-of-rotation arrow on the blade guard

6 must correspond.

–Mount the clamping flange 20 and screw in the clamping

bolt 21.

– Press and hold the spindle lock 13.

–Use the hex key 22 to tighten the clamping bolt 21 (torque

3–5Nm).

Removal of the Diamond Cutting Disc

– Press and hold the spindle lock 13.

–Use the hex key 22 to remove the clamping bolt 21.

– Remove the clamping flange 20 and diamond cutting disc

19 from the drive spindle 17.

Mounting the Hose Kit (see figure B–C)

For wet cutting, use only water as the cooling liquid.

Only fasten the hose kit to the power tool using the screw and

the spring washer intended for this purpose.

Screw the hose connection 24 onto the water tap or to the

outlet of a water container. In order to reach the correct water

pressure, the water container must be positioned at least

80 cm above the working surface of the power tool.

Mount connection hose 23 onto hose fitting 5. Check the tight

seating by pulling on the connection hose.

Regulate the outflowing water quantity via water tap 25 be-

fore putting the power tool into operation.

The maximum permissible water pressure is 0.12 MPa.

Operation

Operating Modes

Before any work on the machine itself, pull the mains

plug.

Pre-selecting the Cutting Depth (see figure D)

The cutting depth may only be pre-selected when the

machine is switched off.

Adapt the cutting depth to the thickness of the workpiece. For

optimum results, the diamond cutting disc must protrude ap-

prox. 2 mm out of the material.

Loosen wing bolt 4. For a smaller cutting depth, pull the ma-

chine from the base plate 8; for a larger cutting depth, push

the machine toward the base plate 8. Adjust the desired cut-

ting depth at the cutting-depth scale 3. Tighten wing bolt 4

again.

Adjusting the Cutting Angle (see figure E)

Loosen wing bolt 8. Tilt the machine sidewards until the de-

sired cutting angle is set on the scale 10. Tighten wing bolt 8

again.

Note: For bevel cuts, the cutting depth is smaller than the set-

ting indicated on the cutting-depth scale 3.

0 cutting mark° (see figure F)

The 0° cutting mark (7) indicates the position of the diamond

cutting disc for straight cuts.

Starting Operation

Observe correct mains voltage! The voltage of the pow-

er source must agree with the voltage specified on the

nameplate of the machine. Power tools marked with

230 V can also be operated with 220 V.

Residual Current Device (RCD)

Check the function of the residual current device (RCD) each

time before starting the operation of the tool!

– Switch the power tool off.

– Insert the mains plug and press the RESET button on the

residual current device (RCD) 14 until the indicator 15

lights up red.

– Press the TEST button on the residual current device

(RCD) 14 until the indicator 15 disappears. If the indicator

15 does not disappear, then the residual current device

(RCD) is faulty and must be repaired.Under no circum-

stances work with the power tool!

– Once the indicator 15 goes off, press the RESET button

again.

– Switch on the machine.

OBJ_BUCH-1810-004.book Page 17 Wednesday, February 4, 2015 11:49 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GDC 125 Professional Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info