Bedienungsanleitung Bosch GDE 18V-16 (Seite 8 von 76) (Alle Sprachen)

786256

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

8 | English

1 609 92A 19U | (30.9.16) Bosch Power Tools

Assembly

Mounting the Dust Extraction Attachment

(see figure A)

– Put the guide groove 11 of the rotary hammer on the hous-

ing guide 9 of the dust extraction attachment and slide the

dust extraction attachment onto the rotary hammer.

The dust extraction attachment must audibly engage.

– To disconnect the attachment, press the unlocking button

8, hold down the unlocking button and pull the dust extrac-

tion attachment off the rotary hammer.

Operation

Working Advice

Never use the dust extraction attachment without a fil-

ter. If the dust extraction attachment is used without a fil-

ter, larger particles of drilling dust can be flung towards the

user and the power tool can be damaged.

Only use an undamaged filter (no cracks, small holes,

etc.). Replace a damaged filter immediately.

Never carry the power tool by the dust extraction at-

tachment.

Note: The guide 4 is spring-loaded. The guide can spring for-

ward when the button 5 for drill bit length adjustment is

pressed.

Inserting/Removing the Drill Bit (see figure B)

– Press the button 5 for drill bit length adjustment and pull

the guide 4 all the way outward.

– Let go of the button 5 again.

– Slide the tip of the drill bit through the dust cap 1/2 from

behind and then fit the bit into the chuck according to the

instructions of your power tool.

– Before removing the drill bit, again press the button 5 and

pull the guide 4 all the way outward.

Adjusting the Guide Length (see figure C)

To ensure that dust is extracted cleanly and the depth stop is

set correctly, the guide 4 must be adjusted so that the tip of

the drill bit is flush at the front with the dust cap 1/2.

Note: To store the dust extraction attachment, press the but-

ton 5 and pull the guide 4 all the way outward. This relieves

strain on the guide’s spring, which increases the lifetime of

the spring.

Adjusting the Drilling Depth (see figure D)

The button 3 for depth stop adjustment can be used to set the

required drilling depth X.

– Press the button 3 and slide the button on the guide 4 so

that the distance X shown in the illustration matches your

required drilling depth.

– Let go of the button 3 again.

Changing the Dust Cap (see figure E)

You will need to change the dust cap 1/2 depending on which

chuck you are using:

–Dust cap 1 for an SDS-plus changeable chuck

–Dust cap 2 for an SDS-plus fixed chuck

You will also need to change the dust cap if the wall contact

surface shows clear signs of wear which is causing dust to es-

cape through the extraction brush during extraction.

Removing the dust cap 1/2:

– Press the locking button 12 and pull the dust cap upwards

out of the holder.

Mounting the dust cap 1/2:

– Insert the new dust cap into the holder from above until the

locking button 12 audibly engages.

Emptying the Dust Box (see figures F1–F4)

Note: Wear a dust mask when performing maintenance and

cleaning on the dust box.

Empty the dust box 13 after completing your work and as

needed, in order to ensure that the dust extraction attach-

ment continues to perform optimally. The viewing window 7

enables you to check how full the dust box is.

– Hold the power tool with the dust extraction attachment

horizontal and switch on the power tool for a few seconds.

This will cause residual dust to be sucked out of the extrac-

tion channel into the dust box 13.

– Insert the required drill bit into

the toolholder of the chuck.

– Press the button 5 while adjust-

ing the guide 4 to match the

drill bit length.

– Let go of the button 5 again.

OBJ_BUCH-2783-001.book Page 8 Friday, September 30, 2016 2:30 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GDE 18V-16 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info