Bedienungsanleitung Bosch GDR 12 V (Seite 20 von 123) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

78928

Zoom out

Zoom in

Vorherige Seite

1/123

Nächste Seite

20 | English

1 609 929 T14 | (18.11.09) Bosch Power Tools

Assembly

Battery Charging

A battery that is new or has not been used for a

longer period does not develop its full capacity

until after approx. 5 charging/discharging cy-

cles.

To remove the battery 5 press the unlocking but-

tons 6 and pull out the battery downwards. Do

not exert any force.

The battery is equipped with a NTC temperature

control which allows charging only within a tem-

perature range of between 0 °C and 45 °C. A

long battery service life is achieved in this man-

ner.

A significantly reduced working period after

charging indicates that the battery is used and

must be replaced.

Observe the notes for disposal.

Changing the Tool (see figure A)

f Before any work on the machine (e. g.,

maintenance, tool change, etc.) as well as

during transport and storage, set the rota-

tional direction switch to the centre posi-

tion. Unintentional actuation of the On/Off

switch can lead to injuries.

GDR 9,6 V/GDR 12 V/GDR 14,4 V/GDR 18 V:

Inserting

Pull the locking sleeve 2 forward, push the in-

sert tool to the stop into the tool holder 1 and

release the locking sleeve 2 to lock the insert

tool.

Use only screwdriver bits with ball catch 11

(DIN 3126-E6.3). Other screwdriver bits 13 can

be used with a universal bit holder with ball

catch 12.

Removing

Pull the locking sleeve 2 forward and remove the

insert tool.

GDS 12 V/GDS 14,4 V/GDS 18 V:

f When working with an application tool, pay

attention that the application tool is firmly

seated on the tool holder. When the applica-

tion tool is not firmly connected with the tool

holder, it can come loose again and not be

controlled.

Slide the application tool onto the square drive

of the tool holder 1.

Operation

Method of Operation

The tool holder 1 with the tool is driven by an

electric motor via a gear and impact mechanism.

The working procedure is divided into two phas-

es:

Screwing in and tightening (impact mechanism

in action).

The impact mechanism is activated as soon as

the screwed connection runs tight and thus load

is put on the motor. In this instance, the impact

mechanism converts the power of the motor to

steady rotary impacts. When loosening screws

or nuts, the process is reversed.

Starting Operation

Inserting the Battery

f Use only original Bosch O-pack batteries

with the voltage given on the type plate of

your machine. The use of other batteries can

lead to injuries and danger of fire.

Set the rotational direction switch 8 to the cen-

tre position in order to avoid unintentional start-

ing. Insert the charged battery 5 into the handle

so that it can be felt to engage and faces flush

against the handle.

Reversing the Rotational Direction

(see figure B)

The rotational direction switch 8 is used to re-

verse the rotational direction of the machine.

However, this is not possible with the On/Off

switch 9 actuated.

OBJ_BUCH-595-002.book Page 20 Wednesday, November 18, 2009 5:13 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GDR 12 V Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info