Bedienungsanleitung Bosch GDR 18 V-EC (Seite 17 von 223) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544091

Zoom out

Zoom in

Vorherige Seite

1/223

Nächste Seite

English | 17

Bosch Power Tools 2 609 140 921 | (3.2.14)

Removing the battery

The battery 4 is equipped with two locking levels that should

prevent the battery from falling out when pushing the battery

unlocking button 5 unintentionally. As long as the battery is

inserted in the power tool, it is held in position by means of a

spring.

To remove the battery 4, press the unlocking button 5 and

pull out the battery toward the front. Do not exert any force.

Changing the Tool

 Before any work on the machine itself (e. g. mainte-

nance, tool change, etc.) as well as during transport

and storage, remove the battery from the power tool.

There is danger of injury when unintentionally actuating

the On/Off switch.

 Regularly clean the power tool’s air vents. The motor’s

fan will draw the dust inside the housing and excessive ac-

cumulation of powdered metal may cause electrical haz-

ards.

GDR 14,4 V-EC/GDR 18 V-EC/GDX 14,4 V-EC/

GDX 18 V-EC:

Inserting

Pull the locking sleeve 2 forward, push the insert tool to the

stop into the tool holder 1 and release the locking sleeve 2 to

lock the insert tool.

Screwdriver bits 16 can be inserted using a universal bit hold-

er with ball lock 15.

Removing

Pull the locking sleeve 2 forward and remove the insert tool.

GDS 14,4 V-EC/GDS 18 V-EC/GDX 14,4 V-EC/

GDX 18 V-EC:

 When working with an application tool, pay attention

that the application tool is connected securely on the

tool holder. When the application tool is not securely con-

nected with the tool holder, it can come off during applica-

tion.

Slide the application tool 17 onto the square drive of the tool

holder 1.

However based on the system, if the application tool 17 ap-

pears wobbly after connecting securely on the tool holder 1;

this has no influence on the function/safety.

GDX 14,4 V-EC/GDX 18 V-EC:

Some application tools (e. g. double bits) cannot be safely se-

cured in the tool holder.

Operation

Method of Operation

The tool holder 1 with the tool is driven by an electric motor

via a gear and impact mechanism.

The working procedure is divided into two phases:

Screwing in and tightening (impact mechanism in action).

The impact mechanism is activated as soon as the screwed

connection runs tight and thus load is put on the motor. In this

instance, the impact mechanism converts the power of the

motor to steady rotary impacts. When loosening screws or

nuts, the process is reversed.

Starting Operation

Inserting the battery

 Use only original Bosch lithium ion batteries with the

voltage listed on the nameplate of your power tool. Us-

ing other batteries can lead to injuries and pose a fire haz-

ard.

Set the rotational direction switch 9 to the centre position to

protect the power tool against accidental starting.

Insert the charged battery 4 from the front into the base of the

power tool until the battery is securely locked.

Reversing the rotational direction (see figure D)

The rotational direction switch 9 is used to reverse the rota-

tional direction of the machine. However, this is not possible

with the On/Off switch 10 actuated.

Right rotation: For driving in screws and tightening nuts,

press the rotational direction switch 9 through to the left

stop.

Left Rotation: For loosening and unscrewing screws and

nuts, press the rotational direction switch 9 through to the

right stop.

Switching On and Off

To start the machine, press the On/Off switch 10 and keep it

pressed.

To switch off the machine, release the On/Off switch 10.

To save energy, only switch the power tool on when using it.

Adjusting the Speed

The speed of the switched on power tool can be variably ad-

justed, depending on how far the On/Off switch 10 is

pressed.

Light pressure on the On/Off switch 10 results in a low rota-

tional speed. Further pressure on the switch results in an in-

crease in speed.

Preselecting the Speed/Impact Frequency

With the button 6 you can preselect the required speed/im-

pact rate in three stages. Press the button 6 repeatedly until

the desired setting appears in the speed indicator 7. The se-

lected setting will be saved.

The required speed/impact frequency depends on the mate-

rial and the working conditions, and can be determined

through practical testing.

OBJ_BUCH-2047-001.book Page 17 Monday, February 3, 2014 11:18 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GDR 18 V-EC Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info