Bedienungsanleitung Bosch GDS 10.8 V-EC Professional (Seite 15 von 202) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

591744

Zoom out

Zoom in

Vorherige Seite

1/202

Nächste Seite

English | 15

Bosch Power Tools 2 609 141 290 | (16.6.15)

nificantly reduce the exposure level over the total working

period.

Identify additional safety measures to protect the operator

from the effects of vibration such as: maintain the tool and the

accessories, keep the hands warm, organisation of work pat-

terns.

Declaration of Conformity

We declare under our sole responsibility that the product de-

scribed under “Technical Data” is in conformity with all rele-

vant provisions of the directives 2009/125/EC (Regulation

1194/2012), 2011/65/EU, until 19 April 2016:

2004/108/EC, from 20 April 2016 on: 2014/30/EU,

2006/42/EC including their amendments and complies with

the following standards: EN 60745-1, EN 60745-2-2.

Technical file (2006/42/EC) at:

Robert Bosch GmbH, PT/ETM9,

70764 Leinfelden-Echterdingen, GERMANY

Robert Bosch GmbH, Power Tools Division

70764 Leinfelden-Echterdingen, GERMANY

Leinfelden, 16.06.2015

Assembly

Removing the Battery (see figure A)

 Use only the battery chargers listed on the accessories

page. Only these battery chargers are matched to the lith-

ium-ion battery of your power tool.

Note: The battery supplied is partially charged. To ensure full

capacity of the battery, completely charge the battery in the

battery charger before using your power tool for the first time.

The lithium-ion battery can be charged at any time without re-

ducing its service life. Interrupting the charging procedure

does not damage the battery.

The lithium-ion battery is protected against deep discharging

by the “Electronic Cell Protection (ECP)”. When the battery is

empty, the machine is switched off by means of a protective

circuit: The inserted tool no longer rotates.

 Do not continue to press the On/Off switch after the

machine has been automatically switched off. The bat-

tery can be damaged.

To remove the battery 8 press the unlocking buttons 7 and

pull out the battery downwards. Do not exert any force.

Observe the notes for disposal.

Changing the Tool

 Before any work on the machine itself (e. g. mainte-

nance, tool change, etc.) as well as during transport

and storage, remove the battery from the power tool.

There is danger of injury when unintentionally actuating

the On/Off switch.

 Regularly clean the power tool’s air vents. The motor’s

fan will draw the dust inside the housing and excessive ac-

cumulation of powdered metal may cause electrical haz-

ards.

GDR 10,8 V-EC:

Inserting (see figure B)

Pull the locking sleeve 2 forward, push the insert tool to the

stop into the tool holder 1 and release the locking sleeve 2 to

lock the insert tool.

Screwdriver bits 15 can be inserted using a universal bit hold-

er with ball lock 14.

Removing

Pull the locking sleeve 2 forward and remove the insert tool.

GDS 10,8 V-EC: (see figure C)

 When working with an application tool, pay attention

that the application tool is connected securely on the

tool holder. When the application tool is not securely con-

nected with the tool holder, it can come off during applica-

tion.

Slide the application tool 16 onto the square drive of the tool

holder 1.

With this system, there will be a slight amount of play around

the application tool 16 after connecting securely to the tool

holder 1; this has no influence on the function/safety.

Operation

Method of Operation

The tool holder 1 with the tool is driven by an electric motor

via a gear and impact mechanism.

The working procedure is divided into two phases:

Screwing in and tightening (impact mechanism in action).

The impact mechanism is activated as soon as the screwed

connection runs tight and thus load is put on the motor. In this

instance, the impact mechanism converts the power of the

motor to steady rotary impacts. When loosening screws or

nuts, the process is reversed.

Starting Operation

Inserting the battery

Set the rotational direction switch 9 to the centre position to

protect the power tool against accidental starting.

Insert the charged battery 8 from the front into the base of the

power tool until the battery is securely locked.

Reversing the rotational direction (see figure D)

The rotational direction switch 9 is used to reverse the rota-

tional direction of the machine. However, this is not possible

with the On/Off switch 10 actuated.

Right rotation: For driving in screws and tightening nuts,

press the rotational direction switch 9 through to the left

stop.

Left Rotation: For loosening and unscrewing screws and

nuts, press the rotational direction switch 9 through to the

right stop.

Henk Becker

Executive Vice President

Engineering

Helmut Heinzelmann

Head of Product Certification

PT/ETM9

OBJ_BUCH-2221-002.book Page 15 Tuesday, June 16, 2015 9:46 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GDS 10.8 V-EC Professional Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info