Bedienungsanleitung Bosch GDS 18V-1000 C (Seite 22 von 307) (Alle Sprachen)

786138

Zoom out

Zoom in

Vorherige Seite

1/307

Nächste Seite

22 | English

rating plate of the power tool. Power tools marked

with 230V can also be operated with 220V.

uProducts that are only sold in AUS and NZ: Use a resid-

ual current device (RCD) with a nominal residual current

of 30 mA or less.

uAlways place the power tool down on its side and do

not lay it on the battery. The power tool can tip over de-

pending on the application tool and battery used.

Inserting the battery

Note: The use of batteries unsuitable for your power tool can

lead to malfunctions or damage to the power tool.

Push the charged battery(5) into the base of the power tool

until the battery is securely locked.

Set the rotational direction (see figureE)

The rotational direction switch (2) is used to change the ro-

tational direction of the power tool. However, this is not pos-

sible while the on/off switch (8) is being pressed.

Right rotation: To drive in screws and tighten nuts, press

the rotational direction switch (2) through to the left stop.

Left Rotation: To loosen and unscrew screws and nuts,

press the rotational direction switch (2) through to the right

stop.

Adjusting the Speed/Impact Rate

You can adjust the speed/impact rate of the power tool when

it is on by pressing in the on/off switch (8) to varying ex-

tents.

Applying light pressure to the on/off switch (8) results in a

low rotational speed/impact rate. Applying increasing pres-

sure to the switch increases the speed/impact rate.

Switching on/off

To start the power tool, press and hold the on/off switch

(8).

The worklight (15) lights up when the on/off switch (8) is

lightly or fully pressed, allowing the work area to be illumin-

ated in poor lighting conditions.

To switch off the power tool, release the on/off switch (8).

User interface (see figures D–E)

GDS 18V-1000C / GDS 18V-1050HC:

The user interface(7) is used to preselect the speed and

working mode and to indicate the status of the power tool.

Status indications

Status indicator for power

tool(11) Meaning/cause Solution

Green Status OK –

Yellow Critical temperature has been reached or re-

chargeable battery is almost empty Run the power tool at no load and allow it to

cool down, or replace or charge the battery

soon

Illuminated red Power tool has overheated or rechargeable

battery is empty Allow the power tool to cool down, or replace

or charge the battery

Flashing blue Power tool is connected to a mobile device or

settings are being transferred –

Speed preselection

With the speed preselection button (16), you can preselect

the required speed in three stages. Press button (16) as of-

ten as needed until the required setting is indicated in the

speed indicator (17). The selected setting will be saved.

GDS 18V-1000C / GDS 18V-1050HC:

You can also preselect the speed using the Bosch Toolbox

app.

The required speed depends on the material and the work-

ing conditions; it can be ascertained through practical tests.

The information in the table below describes the recommen-

ded values.

Basic speed setting at level

123

[min-1] [min-1] [min-1]

Number of speed settings

30–1 100 0–2 300 0–3 400

You can use the button for speed preselection (16) to

preselect the required speed, even during operation.

Switching On the Worklight

GDS 18V-1000 / GDS 18V-1050H:

To switch the worklight(15) on or off, press the worklight

button(13).

uDo not look directly into the worklight; it can blind

you.

Selecting the working mode

GDS 18V-1000C / GDS 18V-1050HC:

The power tool has two preset working modes A and B (12).

You can also programme working modes for different applic-

ations and adjust existing modes via the Bosch Toolbox un-

der A and B (12).

To switch between the working modes A and B (12), press

button (14).

1 609 92A 7X5 | (04.07.2022) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GDS 18V-1000 C Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info