Bedienungsanleitung Bosch GDS 18V-1050 H (Seite 21 von 307) (Alle Sprachen)

786139

Zoom out

Zoom in

Vorherige Seite

1/307

Nächste Seite

English | 21

position. There is risk of injury from unintentionally

pressing the on/off switch.

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Charging the Battery

uUse only the chargers listed in the technical data. Only

these chargers are matched to the lithium-ion battery of

your power tool.

Note: The battery is supplied partially charged. To ensure

full battery capacity, fully charge the battery in the charger

before using your power tool for the first time.

The lithium-ion battery can be charged at any time without

reducing its service life. Interrupting the charging process

does not damage the battery.

The lithium-ion battery is protected against deep discharge

by the "Electronic Cell Protection (ECP)". When the battery

is discharged, the power tool is switched off by means of a

protective circuit: The application tool no longer rotates.

uDo not continue to press the On/Off switch after the

power tool has automatically switched off. The battery

can be damaged.

Follow the instructions on correct disposal.

Removing the Battery

The battery (5) is equipped with two locking levels to pre-

vent the battery from falling out when pushing the battery re-

lease button (6) unintentionally. As long as the battery is in-

serted in the power tool, it is held in position by means of a

spring.

To remove the battery (5), press the release button (6) and

pull the battery out of the power tool. Do not use force to

do this.

Battery charge indicator

The green LEDs on the battery charge indicator indicate the

state of charge of the battery. For safety reasons, it is only

possible to check the state of charge when the power tool is

not in operation.

Press the button for the battery charge indicator or to

show the state of charge. This is also possible when the bat-

tery is removed.

If no LED lights up after pressing the button for the battery

charge indicator, then the battery is defective and must be

replaced.

Battery model GBA 18V...

LEDs Capacity

3× continuous green light 60−100%

2× continuous green light 30−60%

LEDs Capacity

1× continuous green light 5−30%

1× flashing green light 0−5%

Battery model ProCORE18V...

LEDs Capacity

5× continuous green light 80−100%

4× continuous green light 60−80%

3× continuous green light 40−60%

2× continuous green light 20−40%

1× continuous green light 5−20%

1× flashing green light 0−5%

Inserting the Bluetooth® Low Energy Module

GCY42 (Accessory)

Read the corresponding operating instructions for informa-

tion about the Bluetooth® Low Energy ModuleGCY42.

Changing the Tool (see figures A–B)

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

uWhen working with an application tool, pay attention

that the application tool is connected securely to the

tool holder. When the application tool is not securely

connected with the tool holder, it can come off during ap-

plication.

Slide the application tool (10) onto the square drive of the

tool holder (1).

Operation

Method of Operation

The tool holder (1) (with the application tool) is driven by an

electric motor via a gear and impact mechanism.

The working procedure is divided into two phases:

Screwing in and tightening (impact mechanism in action).

The impact mechanism is activated as soon as the screwed

connection runs tight and load is therefore put on the motor.

The impact mechanism then converts the power of the mo-

tor to steady rotary impacts. When loosening screws or nuts,

the process is reversed.

Starting Operation

uPay attention to the mains voltage. The voltage of the

power source must match the voltage specified on the

Bosch Power Tools 1 609 92A 7X5 | (04.07.2022)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GDS 18V-1050 H Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info