Bedienungsanleitung Bosch GDS 18V-210 C (Seite 19 von 279) (Alle Sprachen)

786141

Zoom out

Zoom in

Vorherige Seite

1/279

Nächste Seite

English | 19

possible to check the state of charge when the power tool is

not in operation.

Press the button for the battery charge indicator or to

show the state of charge. This is also possible when the bat-

tery is removed.

If no LED lights up after pressing the button for the battery

charge indicator, then the battery is defective and must be

replaced.

Battery model GBA 18V...

LEDs Capacity

3× continuous green light 60−100%

2× continuous green light 30−60%

1× continuous green light 5−30%

1× flashing green light 0−5%

Battery model ProCORE18V...

LEDs Capacity

5× continuous green light 80−100%

4× continuous green light 60−80%

3× continuous green light 40−60%

2× continuous green light 20−40%

1× continuous green light 5−20%

1× flashing green light 0−5%

Inserting the Bluetooth® Low Energy Module

GCY42 (Accessory)

Read the corresponding operating instructions for informa-

tion about the Bluetooth® Low Energy ModuleGCY42.

Changing the Tool

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Inserting the application tool (see figuresA – B)

GDR 18V-210 C / GDX 18V-210 C:

Pull the locking sleeve (2) forward, guide the application tool

(1) into the tool holder as far as it will go and release the

locking sleeve (2) to lock the application tool.

Impact-proof screwdriver bits(12) can be inserted using a

universal bit holder(13) with ball catch.

Inserting the application tool (see figuresB – C)

GDX 18V-210 C / GDS 18V-210 C:

uWhen working with an application tool, pay attention

that the application tool is connected securely to the

tool holder. When the application tool is not securely

connected with the tool holder, it can come off during ap-

plication.

Slide the application tool (14) onto the square drive of the

tool holder (1).

Due to the way the system operates, the application tool

(14) will move around slightly in the tool holder (1); this has

no influence on the function/safety.

Some application tools (e.g. double bits) cannot be safely

secured in the tool holder.

Removing the application tool (see figuresA – B)

Pull the locking sleeve (2) forward and remove the applica-

tion tool.

Operation

Method of Operation

The tool holder (1) (with the application tool) is driven by an

electric motor via a gear and impact mechanism.

The working procedure is divided into two phases:

Screwing in and tightening (impact mechanism in action).

The impact mechanism is activated as soon as the screwed

connection runs tight and load is therefore put on the motor.

The impact mechanism then converts the power of the mo-

tor to steady rotary impacts. When loosening screws or nuts,

the process is reversed.

Starting Operation

Inserting the battery

Note: The use of batteries unsuitable for your power tool can

lead to malfunctions or damage to the power tool.

Set the rotational direction switch (8) to the centre position

to protect the power tool from being switched on accident-

ally.

Push the charged battery(4) into the base of the power tool

until the battery is securely locked.

Set the rotational direction (see figureD)

The rotational direction switch (8) is used to change the ro-

tational direction of the power tool. However, this is not pos-

sible while the on/off switch (9) is being pressed.

Right rotation: To drive in screws and tighten nuts, press

the rotational direction switch (8) through to the left stop.

Left Rotation: To loosen and unscrew screws and nuts,

press the rotational direction switch (8) through to the right

stop.

Adjusting the Speed/Impact Rate

You can adjust the speed/impact rate of the power tool when

it is on by pressing in the on/off switch (9) to varying ex-

tents.

Bosch Power Tools 1 609 92A 7X4 | (15.08.2022)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GDS 18V-210 C Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info