Bedienungsanleitung Bosch GEX 125-1 AE (Seite 15 von 173) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

78288

Zoom out

Zoom in

Vorherige Seite

1/173

Nächste Seite

English | 15

Bosch Power Tools 1 609 929 S73 | (30.3.11)

Replacing the Sanding Sheet (see figure A)

To remove the sanding sheet 6, lift it from the side and pull it

off of the sanding plate 5.

When attaching a new sanding sheet, remove any dust or

debris from the sanding plate 5, e. g., with a brush.

The surface of the sanding plate 5 is fitted with Velcro backing

for quick and easy fastening of sanding sheets with Velcro ad-

hesion.

Press the sanding sheet 6 firmly against the bottom side of

the sanding plate 5.

To ensure optimum dust extraction, pay attention that the

punched holes in the sanding sheet match with the holes in

the sanding plate.

For easy adjustment of the sanding sheet 6 to the sanding

plate 5, use the adjustment aid in the tool case as shown in the

following figure. Place the sanding sheet into the adjustment

aid with the Velcro facing upward and firmly push on the ma-

chine with the sanding plate.

Selection of the Sanding Plate

Depending on the application, the machine can be equipped

with sanding plates of different hardness:

– Sanding plate, extra soft: Suitable for polishing and sensi-

tive sanding, incl. on convex surfaces.

– Sanding plate, medium hard: Suitable for all sanding work;

universally usable.

– Hard sanding plate: Suitable for high sanding capacity on

flat surfaces.

Replacing the Sanding Plate (see figure B)

Note: Replace a damaged sanding plate 5 immediately.

Pull off the sanding sheet or the polishing accessory. Unscrew

the four screws 7 completely and remove the sanding plate 5.

Attach the new sanding plate 5 and tighten the screws again.

Note: When attaching the sanding plate, pay attention that

the toothing of the drive element engage into the openings of

the sanding plate.

Note: A damaged sanding-plate base may be changed only by

an authorised after-sales service agent for Bosch power tools.

Dust/Chip Extraction

f Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suitable

for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

f Prevent dust accumulation at the workplace. Dusts can

easily ignite.

Integrated Dust Extraction with Dust Box

(see figures C1–C4)

Attach the dust box 3 onto the extraction outlet 8 until it

latches.

The filling level of the dust box 3 can easily be checked

through the transparent container.

To empty the dust box 3, pull it off downward with a light

twisting motion.

Before opening the dust box 3, it is recommended to loosen

the dust from the filter element by gently striking it against a

firm support (as shown in the figure).

Hold the dust box 3 firmly, fold the filter element 9 upward

and empty the dust box. Clean the thin plates of the filter

element 9 with a soft brush.

External Dust Extraction (see figure D)

Attach a vacuum hose 10 onto the outlet piece 8. Connect the

vacuum hose 10 with a vacuum cleaner. An overview for

connecting to various vacuum cleaners can be found at the

beginning of these operating instructions.

The vacuum cleaner must be suitable for the material being

worked.

When vacuuming dry dust that is especially detrimental to

health or carcinogenic, use a special vacuum cleaner.

Operation

Starting Operation

f Observe correct mains voltage! The voltage of the pow-

er source must agree with the voltage specified on the

nameplate of the machine. Power tools marked with

230 V can also be operated with 220 V.

Switching On and Off

To start the machine, tilt the On/Off switch 1 toward the right

to the “I” position.

To switch off the machine, tilt the On/Off switch 1 toward the

left to the “0” position.

OBJ_BUCH-315-004.book Page 15 Wednesday, March 30, 2011 8:18 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GEX 125-1 AE Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info