Bedienungsanleitung Bosch GEX 18V-125 (Seite 17 von 221) (Alle Sprachen)

786279

Zoom out

Zoom in

Vorherige Seite

1/221

Nächste Seite

English | 17

Operation

Starting Operation

Switching On/Off

uMake sure that you are able to press the On/Off switch

without releasing the handle.

To switch on the power tool, press the on/off switch(1).

To switch off the power tool, press the on/off switch(1)

again.

Preselecting the orbital stroke rate

You can even preselect the orbital stroke rate during opera-

tion using the necessary orbital stroke rate preselection

thumbwheel (7).

1–2 Low orbital stroke rate

3–4 Medium orbital stroke rate

5–6 High orbital stroke rate

The required orbital stroke rate is dependent on the material

and the work conditions and can be determined using prac-

tical tests.

The Constant Electronic keeps the orbital stroke rate at no

load and under load virtually consistent, guaranteeing uni-

form performance.

After working at a low orbital stoke rate for an extended

period, you should operate the power tool at the maximum

orbital stroke rate for approximately three minutes without

load to cool it down.

Application Overview

Application/Material Abrasive Speed setting

Removing – Removing old paint and varnish

– Sanding wood

P60–P100 4–6

– Sanding thermoplastic synthetic materials P60–P100 1–3

Preparing – Sanding wood and veneer prior to painting

– Edge chamfering on wooden materials

– Smoothing wooden surfaces before staining

P120–P180 4–6

– Intermediate lacquer sanding and sanding undercoats

– Intermediate lacquer sanding on edges

P220–P280 1–3

Finishing – Sanding wood

– Sanding solid wood edges and veneer edges

P150–P180 4–6

– Lacquer sanding on stained surfaces and edges P240–P320 1–3

Working Advice

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

uAlways wait until the power tool has come to a com-

plete stop before placing it down.

uThis power tool is not suitable for bench-mounted use.

It must not be clamped into a vice or fastened to a work-

bench, for example.

For fatigue-free work, you can hold the power tool from

above, from the side or from the front, depending on the ap-

plication (see figureG).

Sanding Surfaces

Switch the power tool on, place the entire sanding surface

against the surface of the workpiece and apply moderate

pressure as you move the sander over the workpiece.

The material removal rate and sanding result are primarily

determined by the choice of sanding sheet, the preselected

orbital stroke rate level and the contact pressure.

Only immaculate sanding sheets achieve good sanding per-

formance and make the power tool last longer.

Be sure to apply consistent contact pressure in order to in-

crease the lifetime of the sanding sheets.

Excessively increasing the contact pressure will not lead to

increased sanding performance, rather it will cause more

severe wear of the power tool and of the sanding sheet.

Use only original Bosch-sanding accessories.

Rough Sanding

Attach a coarse grit sanding sheet.

Apply only light pressure to the power tool so that it runs at a

higher orbital stroke rate and a higher material removal rate

is achieved.

Fine Sanding

Attach a fine grit sanding sheet.

You can reduce the sanding plate orbital stroke rate by

lightly varying the contact pressure or changing the orbital

stroke rate level; the random orbit motion will be retained.

Move the power tool with moderate pressure flat on the

workpiece in a circular motion or alternately along and

across it. Do not tilt the power tool in order to avoid sanding

through the workpiece, e.g. veneers.

Switch the power tool off after completing operation.

Bosch Power Tools 1 609 92A 7N0 | (17.05.2022)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GEX 18V-125 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info