786469

Bosch GEX 34-125 Seite 15

15
Zoom out
Zoom in
Vorherige Seite
1/193
Nächste Seite
English | 15
The required orbital stroke rate is dependent on the material
and the work conditions and can be determined using prac-
tical tests.
The Constant Electronic keeps the orbital stroke rate at no
load and under load virtually consistent, guaranteeing uni-
form performance.
After working at a low orbital stoke rate for an extended
period, you should operate the power tool at the maximum
orbital stroke rate for approximately three minutes without
load to cool it down.
Sanding Plate Brake
An integrated sanding pad brake reduces the orbital stroke
rate when running without load to prevent scoring when the
power tool is placed on the workpiece.
If the no-load orbital stroke rate constantly increases over
time, this means that the sanding pad is damaged and must
be replaced, or that the sanding pad brake is worn. A worn
sanding pad brake must be replaced by an after-sales ser-
vice centre authorised to work with Bosch power tools.
Working Advice
uPull the plug out of the socket before carrying out any
work on the power tool.
uAlways wait until the power tool has come to a com-
plete stop before placing it down.
uThis power tool is not suitable for bench-mounted use.
It must not be clamped into a vice or fastened to a work-
bench, for example.
Sanding Surfaces
Switch the power tool on, place the entire sanding surface
against the surface of the workpiece and apply moderate
pressure as you move the sander over the workpiece.
The material removal rate and sanding result are primarily
determined by the choice of sanding sheet, the preselected
orbital stroke rate level and the contact pressure.
Only immaculate sanding sheets achieve good sanding per-
formance and make the power tool last longer.
Be sure to apply consistent contact pressure in order to in-
crease the lifetime of the sanding sheets.
Excessively increasing the contact pressure will not lead to
increased sanding performance, rather it will cause more
severe wear of the power tool and of the sanding sheet.
Do not use a sanding sheet for other materials after it has
been used to work on metal.
Use only original Bosch-sanding accessories.
Rough Sanding
Attach a coarse grit sanding sheet.
Apply only light pressure to the power tool so that it runs at a
higher orbital stroke rate and a higher material removal rate
is achieved.
Fine Sanding
Attach a fine grit sanding sheet.
You can reduce the sanding plate orbital stroke rate by
lightly varying the contact pressure or changing the orbital
stroke rate level; the random orbit motion will be retained.
Move the power tool with moderate pressure flat on the
workpiece in a circular motion or alternately along and
across it. Do not tilt the power tool in order to avoid sanding
through the workpiece, e.g. veneers.
Switch the power tool off after completing operation.
Polishing
For polishing weathered lacquers and redressing scratches
(e.g. acrylic glass), the power tool can be fitted with an ap-
propriate polishing tool, e.g. lambswool bonnet, polishing
felt or polishing sponge (accessory).
Select a low orbital stroke rate (level 1–2) when polishing in
order to avoid heating up the surface excessively.
Apply the polish to an area slightly smaller than the area
which you intend to polish. Using the appropriate polishing
tool, work in the polish with either linear or circular move-
ments and with moderate pressure.
Do not allow the polish to dry out on the surface; this may
damage the surface. Do not expose the surface which you in-
tend to polish to direct sunlight.
Clean the polishing tool regularly to ensure good polishing
results. Wash the polishing tools with mild detergent and
warm water; do not use thinning agents.
Maintenance and Service
Maintenance and Cleaning
uPull the plug out of the socket before carrying out any
work on the power tool.
uTo ensure safe and efficient operation, always keep
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
Bosch Power Tools 1 609 92A 7T6 | (21.06.2022)
… 15 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch GEX 34-125 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info