Bedienungsanleitung Bosch GFF 22 A Professional (Seite 16 von 173) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

593208

Zoom out

Zoom in

Vorherige Seite

1/173

Nächste Seite

16 | English

1 609 929 N81 | (18.5.11) Bosch Power Tools

– Loosen the clamping screw 32 by approx. 3 turns.

Note: Do not completely unscrew the clamping screw 32

so that the lock washer 31 is not lost. Without the lock

washer, the base plate 33 cannot be secured.

– Pivot the base plate 33 upward. Hold the machine in such

a manner that the base plate will not pivot back.

– Press the spindle lock button 14 and keep it pressed.

– Loosen and remove the clamping nut 24 with the two-pin

spanner 23 provided.

– Remove the cutting disc 25 if mounted, and clean it.

– Remove the mounting flange 28 if mounted, and clean it.

– Place the mounting flange 28 onto the cutter spindle 29 in

such a manner that the centring collar 27 (22 mm diame-

ter) faces upward. The flats of the mounting flange must

engage onto the flats of the cutter spindle (anti-twist pro-

tection).

– Place the clean cutting disc 25 as shown in the figure onto

the mounting flange 28 in such a manner that the direction-

of-rotation arrow on the cutting disc 26 is visible and corre-

sponds with the direction-of-rotation arrow of the cutter

spindle 30. The mounting bore of the cutting disc must

engage in the centring collar 27 of the mounting flange.

– Screw the clamping nut 24 onto the cutter spindle 29.

With the spindle lock button 14 pressed, firmly tighten the

clamping nut with the two-pin spanner 23.

f Check if the cutting disc is properly mounted and ro-

tates freely.

– Pivot the base plate 33 down. Pay attention that the lock

washer 31 rests on the base plate (with the clamping screw

32 alone the base plate cannot be fastened securely).

– Tighten the clamping screw 32.

f Check if the base plate 33 is locked securely.

Dust/Chip Extraction

f Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suitable

for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

Clean the vacuum connection 21, if required. For this, pivot

up the base plate 33 (see “Installing/Replacing the Cutting

Disc”, page 15) and pull off the vacuum connection.

External Dust Extraction (see Accessory Page)

Insert the extraction adapter (accessory) with a light turning

motion into the vacuum connection 21. Insert the sleeve of a

vacuum hose (accessory) with a turning motion into the extrac-

tion adapter. Connect the vacuum hose to a vacuum cleaner.

The vacuum cleaner must be suitable for the material being

worked.

When vacuuming dry dust that is especially detrimental to

health or carcinogenic, use a special vacuum cleaner.

Internal Dust Extraction with Dust Bag

(see Accessory Page)

For small cutting jobs, the dust bag 22 can be used.

Insert the sleeve of the dust bag 22 with a light turning motion

into the vacuum connection 21.

To maintain optimum dust collection, empty the dust bag 22

in good time.

For this, pull off the dust bag 22, open the zipper and empty

the dust bag.

Operation

Adjusting the Depth-of-cut

With the cutting depth adjustment knob 18, the depth-of-cut

can be set. The cutting depth adjustment knob has set stops

for six biscuit dowel sizes.

Correlation of the set stops to biscuit dowel sizes and depths-

of-cut:

When using resharpened cutting discs, the depth-of-cut may

possibly need to be readjusted. For this, loosen the lock nut

19. The depth-of-cut can be reduced by turning the knurled

screw 20 in clockwise direction or increased by turning in an-

ticlockwise direction. Check the adjusted cutting depth by

carrying out trial cuts. Afterwards, firmly tighten the lock nut

19 again.

Setting the Adjustable Height Stop

With the adjustable height stop 9, the distance between the

upper surface of the workpiece and the intended groove can

be set.

Set stop Biscuit dowel Depth-of-cut in mm

No. 0 8

No. 10 10

No. 20 12.3

Simplex 13

Duplex 14.7

MAX

–22

OBJ_BUCH-268-003.book Page 16 Wednesday, May 18, 2011 11:03 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GFF 22 A Professional Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info