Bedienungsanleitung Bosch GGS 18 H (Seite 11 von 183) (Alle Sprachen)

786343

Zoom out

Zoom in

Vorherige Seite

1/183

Nächste Seite

English | 11

Bosch Power Tools 1 609 92A 2NY | (21.3.16)

Safety Warnings for Die Grinders

Safety Warnings common for Grinding and Sanding

This power tool is intended to function as a grinder and

sander. Read all safety warnings, instructions, illustra-

tions and specifications provided with this power tool.

Failure to follow all instructions listed below may result in

electric shock, fire and/or serious injury.

Operations such as wire brushing, polishing or cutting-

off are not recommended to be performed with this

power tool. Operations for which the power tool was not

designed may create a hazard and cause personal injury.

Do not use accessories which are not specifically de-

signed and recommended by the tool manufacturer.

Just because the accessory can be attached to your power

tool, it does not assure safe operation.

The rated speed of the grinding accessories must be at

least equal to the maximum speed marked on the pow-

er tool. Grinding accessories running faster than their rat-

ed speed can break and fly apart.

The outside diameter and the thickness of your acces-

sory must be within the capacity rating of your power

tool. Incorrectly sized accessories cannot be adequately

controlled.

The arbour size of wheels, sanding drums or any other

accessory must properly fit the spindle or collet of the

power tool. Accessories that do not match the mounting

hardware of the power tool will run out of balance, vibrate

excessively and may cause loss of control.

Mandrel-mounted wheels, sanding drums, cutters or

other accessories must be inserted fully into the collet

or chuck. If the mandrel is insufficiently held and/or the

overhang of the wheel is too long, the mounted wheel may

become loose and be ejected at high velocity.

Do not use a damaged accessory. Before each use in-

spect the accessory such as abrasive wheels for chips

and cracks, sanding drum for cracks, tear or excess

wear, wire brush for loose or cracked wires. If power

tool or accessory is dropped, inspect for damage or in-

stall an undamaged accessory. After inspecting and in-

stalling an accessory, position yourself and bystanders

away from the plane of the rotating accessory and run

the power tool at maximum no-load speed for one min-

ute. Damaged accessories will normally break apart during

this test time.

Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety

glasses. As appropriate, wear dust mask, hearing pro-

tectors, gloves and workshop apron capable of stop-

ping small abrasive or workpiece fragments. The eye

protection must be capable of stopping flying debris gen-

erated by various operations. The dust mask or respirator

must be capable of filtrating particles generated by your

operation. Prolonged exposure to high intensity noise may

cause hearing loss.

Keep bystanders a safe distance away from work area.

Anyone entering the work area must wear personal

protective equipment. Fragments of workpiece or of a

broken accessory may fly away and cause injury beyond

immediate area of operation.

Hold power tool only by the insulated gripping surfaces

only, when performing an operation where the cutting

accessory may contact hidden wiring or its own cord.

Cutting accessory contacting a “live” wire may make ex-

posed metal parts of the power tool “live” and could give

the operator an electric shock.

Always hold the tool firmly in your hand(s) during the

start-up. The reaction torque of the motor, as it acceler-

ates to full speed, can cause the tool to twist.

Use clamps to support workpiece whenever practical.

Never hold a small workpiece in one hand and the tool

in the other hand while in use. Clamping a small work-

piece allows you to use your hand(s) to control the tool.

Round material such as dowel rods, pipes or tubing have a

tendency to roll while being cut, and may cause the bit to

bind or jump toward you.

Position the cord clear of the spinning accessory. If you

lose control of the power tool, the cord may be cut or

snagged and your hand or arm may be pulled into the spin-

ning accessory.

Never lay the power tool down until the accessory has

come to a complete stop. The spinning accessory may

grab the surface and pull the power tool out of your control.

After changing the bits or making any adjustments,

make sure the collet nut, chuck or any other adjust-

ment devices are securely tightened. Loose adjustment

devices can unexpectedly shift, causing loss of control,

loose rotating components will be violently thrown.

Do not run the power tool while carrying it at your side.

Accidental contact with the spinning accessory could snag

your clothing, pulling the accessory into your body.

Regularly clean the power tool’s air vents. The motor’s

fan will draw the dust inside the housing and excessive ac-

cumulation of powdered metal may cause electrical haz-

ards.

Do not operate the power tool near flammable materi-

als. Sparks could ignite these materials.

Do not use accessories that require liquid coolants. Us-

ing water or other liquid coolants may result in electrocu-

tion or shock.

Kickback and related warnings

Kickback is a sudden reaction to a pinched or snagged ro-

tating wheel, sanding band, brush or any other accessory.

Pinching or snagging causes rapid stalling of the rotating

accessory which in turn causes the uncontrolled power

tool to be forced in the direction opposite of the accesso-

ry’s rotation.

For example, if an abrasive wheel is snagged or pinched by

the workpiece, the edge of the wheel that is entering into

the pinch point can dig into the surface of the material

causing the wheel to climb out or kick out. The wheel may

either jump toward or away from the operator, depending

on direction of the wheel’s movement at the point of pinch-

ing. Abrasive wheels may also break under these condi-

tions.

OBJ_BUCH-1048-005.book Page 11 Monday, March 21, 2016 2:41 PM

Bosch GGS 18 H Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info