Bedienungsanleitung Bosch GGS 28 LP Professional (Seite 12 von 153) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

592518

Zoom out

Zoom in

Vorherige Seite

1/153

Nächste Seite

12 | English

3 609 929 C27 | (2.3.12) Bosch Power Tools

Product Features

The numbering of the product features refers to the illustra-

tion of the machine on the graphics page.

1 Collet

2 Clamping nut

3 Grinder spindle

4 Spindle collar

5 On/Off switch

6 Lock-off button for On/Off switch

7 Handle (insulated gripping surface)

8 Open-end spanner on the grinder spindle*

9 Open-end spanner applied to clamping nut*

*Accessories shown or described are not part of the standard de-

livery scope of the product. A complete overview of accessories

can be found in our accessories program.

Technical Data

Noise/Vibration Information

Measured sound values determined according to EN 60745.

Typically the A-weighted noise levels of the product are:

Sound pressure level 80 dB(A); Sound power level 91 dB(A).

Uncertainty K =3 dB.

Wear hearing protection!

Vibration total values a

(triax vector sum) and Uncertainty K

determined according to EN 60745:

Surface grinding (with wheel diameter of 25 mm):

=6.0m/s

, K=1.5 m/s

Surface grinding (with wheel diameter of 50 mm):

=20.0 m/s

, K=1.5 m/s

The vibration emission level given in this information sheet

has been measured in accordance with a standardised test

given in EN 60745 and may be used to compare one tool with

another. It may be used for a preliminary assessment of expo-

sure.

The declared vibration emission level represents the main ap-

plications of the tool. However if the tool is used for different

applications, with different accessories or poorly maintained,

the vibration emission may differ. This may significantly in-

crease the exposure level over the total working period.

An estimation of the level of exposure to vibration should also

take into account the times when the tool is switched off or

when it is running but not actually doing the job. This may sig-

nificantly reduce the exposure level over the total working pe-

riod.

Identify additional safety measures to protect the operator

from the effects of vibration such as: maintain the tool and the

accessories, keep hands warm, organise work patterns.

Declaration of Conformity

We declare under our sole responsibility that the product de-

scribed under “Technical Data” is in conformity with the fol-

lowing standards or standardization documents: EN 60745

according to the provisions of the directives 2011/65/EU,

2004/108/EC, 2006/42/EC.

Technical file (2006/42/EC) at:

Robert Bosch GmbH, PT/ETM9,

D-70745 Leinfelden-Echterdingen

Robert Bosch GmbH, Power Tools Division

D-70745 Leinfelden-Echterdingen

16.02.2012

Assembly

f Before any work on the machine itself, pull the mains

plug.

Mounting the Grinding Tools (see figure A)

f Only use properly fitting and undamaged open-end

spanners (see “Technical Data”).

– Clean the grinder spindle 3 and all parts to be mounted.

– Hold the grinder spindle 3 with open-end spanner 8 by the

spanner flats.

Loosen the clamping nut 2 with open-end spanner 9 by ap-

plying it to the spanner flats and turning in anticlockwise

direction.

– Insert the clamping shaft of the grinding tool to the stop in-

to the collet chuck 1.

– Hold the grinder spindle 3 firmly with open-end spanner 8

and clamp the tool bit with open-end spanner 9 by the

spanner flats, turning in clockwise direction.

The grinding tools must run completely concentrical. Do not

continue to use out-of-round grinding accessories, instead,

replace before continuing to work.

f Do not tighten the collet chuck of the clamping nut as

long as no grinding accessory is mounted. Otherwise,

the collet chuck can become damaged.

Straight grinder GGS 28 LP

Article number

3 601 B25 0..

Rated power input

W500

Output power

W280

Rated speed

min

-1

29000

Collet chuck diameter, max.

mm 8

Spanner size of

–clamping nut

– grinder spindle

Spindle collar dia.

– with rubber cap

– without rubber cap

Thickness of grinding wheels, max.

mm 32

Grinding tool diameter, max.

mm 40

Weight according to

EPTA-Procedure 01/2003

kg 1.7

Protection class

/II

The values given are valid for a nominal voltage [U] of 230 V. For differ-

ent voltages and models for specific countries, these values can vary.

Dr. Egbert Schneider

Senior Vice President

Engineering

Helmut Heinzelmann

Head of Product Certification

PT/ETM9

OBJ_BUCH-1580-002.book Page 12 Friday, March 2, 2012 12:19 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GGS 28 LP Professional Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info