Bedienungsanleitung Bosch GHO 18 V-LI Professional (Seite 15 von 199) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

593161

Zoom out

Zoom in

Vorherige Seite

1/199

Nächste Seite

English | 15

Bosch Power Tools 1 609 92A 0KP | (13.5.14)

Technical file (2006/42/EC) at:

Robert Bosch GmbH, PT/ETM9,

70764 Leinfelden-Echterdingen, GERMANY

Robert Bosch GmbH, Power Tools Division

70764 Leinfelden-Echterdingen, GERMANY

Leinfelden, 25.03.2014

Assembly

 Before any work on the machine itself (e. g. mainte-

nance, tool change, etc.) as well as during transport

and storage, remove the battery from the power tool.

There is danger of injury when unintentionally actuating

the On/Off switch.

Battery Charging (see figure A)

 Use only the battery chargers listed on the accessories

page. Only these battery chargers are matched to the lith-

ium-ion battery of your power tool.

Note: The battery supplied is partially charged. To ensure full

capacity of the battery, completely charge the battery in the

battery charger before using your power tool for the first time.

The lithium-ion battery can be charged at any time without re-

ducing its service life. Interrupting the charging procedure

does not damage the battery.

The lithium-ion battery is protected against deep discharging

by the “Electronic Cell Protection (ECP)”. When the battery is

empty, the machine is switched off by means of a protective

circuit: The inserted tool no longer rotates.

 Do not continue to press the On/Off switch after the

machine has been automatically switched off. The bat-

tery can be damaged.

To remove the battery 7 press the unlocking buttons 8 and

pull out the battery downwards. Do not exert any force.

The Hex key 12 required for replacement of the planer blade is

located inside the machine and should always be stored there.

Observe the notes for disposal.

Battery Charge-control Indication (see figure B)

The three green LEDs of the battery charge-control indicator

14 indicate the charge condition of the battery 7. For safety

reasons, it is only possible to check the status of the charge

condition when the machine is at a standstill.

Press button 13 to indicate the charge condition. This is also

possible when the battery 7 is removed.

When no LED lights up after pushing button 13, then the bat-

tery is defective and must be replaced.

Changing the Tool

 Be cautious when replacing the planer blades. Do not

grasp the planer blades by the cutting edges. Possible

danger of injury due to the sharp cutting edges of the plan-

er blades.

Use only original Bosch carbide blades (TC).

The carbide blade (TC) has 2 cutting edges and can be re-

versed. When both cutting edges are dull, the planer blade 18

must be replaced. The carbide blade (TC) may not be resharp-

ened.

Disassembling the Planer Blade(s) (see figure C)

To reverse or replace the planer blade 18, rotate the blade

drum 15 until it is parallel to the planer base plate 10.

 Loosen the two fastening screws 17 with the Hex key 12

by approx. 1–2turns.

 If necessary, loosen the clamping element 16 by giving it

a light blow with a suitable tool (e.g. a wooden wedge).

 Push the planer blade 18 sidewards out of the blade

drum 15 with a piece of wood.

Assembling the Planer Blade(s) (see figure D)

The guide groove of the planer blade always ensures continu-

ous height adjustment when replacing or reversing it.

If required, clean the blade seat in the clamping element 16

and the planer blade 18.

When assembling the planer blade, ensure that it is seated

properly in the blade holder of the clamping element 16 and

aligned flush at the side edge of the rear planer base plate 10.

Afterwards tighten the 2 fastening screws 17 again with the

Hex key 12.

Note: Before restarting, check if the fastening screws 17 are

tightened well. Rotate the blade drum 15 by hand and ensure

that the planer blade does not graze.

Dust/Chip Extraction

 Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suitable

for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the mate-

rials to be worked.

Clean the chip ejector 1 regularly. Use a suitable tool (e.g., a

piece of wood, compressed air, etc.) to clean a clogged chip

ejector.

Henk Becker

Executive Vice President

Engineering

Helmut Heinzelmann

Head of Product Certification

PT/ETM9

LED Capacity

Continuous lighting 3 x green ≥ 2/3

Continuous lighting 2 x green ≥ 1/3

Continuous lighting 1 x green <1/3

Flashing light 1 x green Reserve

OBJ_BUCH-1520-004.book Page 15 Tuesday, May 13, 2014 2:26 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GHO 18 V-LI Professional Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info