Bedienungsanleitung Bosch GHO 26-82 D (Seite 15 von 185) (Alle Sprachen)

786476

Zoom out

Zoom in

Vorherige Seite

1/185

Nächste Seite

English | 15

– Provide good ventilation at the workplace.

– It is advisable to wear a P2 filter class breathing mask.

The regulations on the material being machined that apply in

the country of use must be observed.

uAvoid dust accumulation at the workplace. Dust can

easily ignite.

Clean the chip ejector (3) regularly. Clean a clogged chip

ejector using a suitable tool, e.g. a piece of wood, com-

pressed air, etc.

uDo not allow the chip ejector to come into contact with

your hands. You may be injured by rotating parts.

Always use an external dust extraction device or chip/dust

bag to guarantee optimum suction.

External dust extraction (see figure C)

Connect an extraction hose (15) (accessory) to the chip

ejector (3).

Connect the extraction hose (15) to a dust extractor (ac-

cessory). You will find an overview of how to connect to vari-

ous dust extractors at the end of these operating instruc-

tions. The dust extractor must be suitable for the material

being worked.

When extracting dry dust that is especially detrimental to

health or carcinogenic, use a special dust extractor.

Self-generated dust extraction (see figure C)

A chip/dust bag (accessory) (16) can be used for smaller

jobs. Insert the dust bag nozzle of the chip/dust bag firmly

into the chip ejector (3). Empty the chip/dust bag (16) at

regular intervals to maintain optimum dust collection.

Adjustable chip ejector (GHO 26-82 D)

Using the changeover lever (6), the chip ejector can be (3)

adjusted to the right or left. Always push the changeover

lever (6) towards the end position until it clicks into place.

The selected chip ejector direction is indicated by an arrow

symbol on the changeover lever (6).

Operation

Start-up

uPay attention to the mains voltage. The voltage of the

power source must match the voltage specified on the

rating plate of the power tool. Power tools marked

with 230V can also be operated with 220V.

uProducts that are only sold in AUS and NZ: Use a resid-

ual current device (RCD) with a nominal residual current

of 30 mA or less.

Setting the cutting depth

Using the knob (2), the cutting depth can be continuously

adjusted between 0–1.6 mm (GHO 16-82) or 0–2.6 mm

(GHO 26-82 D) with the aid of the cutting depth scale (1)

(scale division = 0.1 mm).

Switching on/off

uMake sure that you are able to press the On/Off switch

without releasing the handle.

To start the power tool, first press the lock-off switch(4),

then press and hold the on/off switch(5).

To switch off the power tool, release the on/off switch(5).

Note: For safety reasons, the on/off switch(5) cannot be

locked; it must remain pressed during the entire operation.

Practical advice

uPull the plug out of the socket before carrying out any

work on the power tool.

Parking rest (see figure D)

The parking rest (25) makes it possible to put down the

power tool directly after working, without any danger of

damaging the workpiece or planer blade. During the work

process, the parking rest (25) is highly pivoted and the rear

section of the planer base plate (7) is released.

Note: The parking rest (25) must not be removed.

Planing Procedure (see figure D)

Set the required cutting depth and position the power tool

with the front section of the planer base plate (7) on the

workpiece.

uOnly bring the power tool into contact with the work-

piece when switched on. Otherwise there is danger of

kickback if the cutting tool jams in the workpiece.

Switch on the power tool and guide it over the surface of the

workpiece, applying uniform feed.

To achieve high-quality surfaces, apply only a low feed rate

and exert pressure on the middle of the planer base plate.

For the processing of hard materials, such as hardwood, and

also when utilising the maximum planing width, set only a

low cutting depth and reduce the planer feed as appropriate.

Excessive feed reduces the quality of the surface finish and

can lead to the chip ejector quickly becoming blocked.

Only sharp planer blades achieve good cutting performance

and make the power tool last longer.

The integrated parking rest (25) also enables a continuation

of the planing procedure following interruption at any point

on the workpiece:

– Place the power tool – with parking rest folded down –

onto the area of the workpiece that you will continue to

work on.

– Switch the power tool on.

– Shift the contact pressure onto the front of the planer

base plate and slowly slide the power tool forward (). In

doing so, the parking rest will swivel upwards and out of

the way (), meaning that the rear section of the planer

base plate is in contact with the workpiece again.

– Guide the power tool over the surface of the workpiece,

applying uniform feed ().

Chamfering edges (see figure E)

The V-groove (8) in the front of the planer base plate enables

quick and easy chamfering of workpiece edges. Position the

planer with the V-groove onto the edge of the workpiece and

guide it along.

Bosch Power Tools 1 609 92A 7X9 | (03.08.2022)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GHO 26-82 D Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info