Bedienungsanleitung Bosch GHP 5-65 (Seite 16 von 283) (Alle Sprachen)

733409

Zoom out

Zoom in

Vorherige Seite

1/283

Nächste Seite

16 | English

1 609 92A 3EV | (16.5.17) Bosch Power Tools

Noise/Vibration Information

Connecting to the water supply

(see figure F)

Note: Rated output pressure can only be achieved, if the flow

rate at the water input is sufficient. The flow rate is sufficient

if a 10 litre bucket can be filled in less than 1 minute.

CAUTION: Permanent operation with lack of water at the wa-

ter input can damage the pump.

NOTE: For a sufficient water supply use a short hose with a di-

ameter not thinner than 1/2" (13 mm). Hoses longer than

10 m should have a diameter of 3/4" (19 mm). Open the wa-

ter tap completely. All connections must be tight. Clean the

water filters periodically (see chapter Maintenance).

– It is recommended to use always an external water filter

(accessory). Check water filter for tight assembly.

– If necessary, screw on an hose adapter (not supplied with

the machine).

– Connect a suitable water hose, best with 1/2" (13 mm) or

3/4" (19 mm) diameter.

– Open the water tap completely and check all connections

for tightness.

Connecting to the mains (see figure G)

NOTE: Rated output pressure is only available, if the machine

is connected to a stable mains voltage. Using a long connec-

tion cable with a thin wire cross section, an uncoiled cable

drum, operating other machines concurrently at the same cir-

cuit or voltage fluctuations outside accessible tolerances im-

pede motor starting or result in low output pressure.

Bleeding high-pressure washer and

hoses (see figure G)

NOTE: Bleed the unit each time the water hose is connected

to the water tab according the following procedure:

Leave the main switch at OFF (0) position.

Disconnect the lance from the gun.

– As soon the trigger of the gun is operated, air and water ex-

its noisily. Hold the trigger until water exits steadily from

the gun. Release the trigger.

– Reconnect the lance.

– Switch on the machine for operation.

– Press the safety release and operate the trigger of the gun.

Use with alternative water sources

(see figure I)

This high-pressure washer will self prime and can draw water

from water tanks and natural water sources. It’s IMPORTANT

that the water is clean and both BOSCH inlet filter and exter-

nal filter are clear and fitted to the machine (see chapter Main-

tenance).

Open tanks/containers and natural

water sources (see figure I)

Use the Self Priming accessory kit comprising:

– Inlet strainer with non return valve

– 3 m reinforced supply hose

– Universal coupling to the pressure washer

This enables the pressure washer to draw water up to 0.5 m

above the water level in the source in approximately 25 – 50

seconds.

Fully immerse the 3 m hose into the water to

displace the air in the hose. Connect the 3 m

hose to the power washer and make sure that

the inlet strainer remains under water.

Run the pressure washer with the lance disconnected until a

steady flow of water appears from the high pressure hose.

Stop if this has not been achieved within 25– 50 seconds and

check all the connections. Switch off and connect the lance

and nozzle to operate.

It is important that hose and couplings are of good quality and

are tightly connected, and that the seals are undamaged and

properly inserted. Loose connections can impede the priming

(drawing in).

Sound emission values determined according to

EN 60335-2-79.

Typically the A-weighted noise levels of the

product are:

Sound pressure level

Sound power level

Uncertainty K

Wear hearing protection!

dB(A)

=2.5

=2.3

Vibration total values ah (triax vector sum) and

uncertainty K determined according to

EN 60335-2-79:

Vibration emission value ah

Uncertainty K m/s2

m/s2=1.841

=1.5 =1.841

=1.5

OBJ_BUCH-2319-004.book Page 16 Tuesday, May 16, 2017 11:15 AM

3 600 … J10 4.. J10 9.. J10 5.. J10 6.. J10 7.. J10 8..

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GHP 5-65 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info