Bedienungsanleitung Bosch GKE 40 BCE (Seite 25 von 153) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

79225

Zoom out

Zoom in

Vorherige Seite

1/153

Nächste Seite

English - 8

Bucking a Log

Bucking is cutting a log into lengths. It is impor-

tant to make sure your footing is firm and your weight

is evenly distributed on both feet. When possible,

the log should be raised and supported by the use of

limbs, logs or chocks. Follow the simple directions

for easy cutting.

When the log is supported along its entire length as

illustrated, it is cut from the top (overbuck).

When the log is supported on one end, as illus-

trated, cut 1/3 the diameter from the underside (un-

derbuck). Then make the finished cut by overbuck-

ing to meet the first cut.

When the log is supported on both ends, as illus-

trated, cut 1/3 the diameter from the top overbuck.

Then make the finished cut by underbucking the

lower 2/3 to meet the first cut.

When bucking on a slope always stand on the

uphill side of the log, as illustrated. When "cutting

through”, to maintain complete control release the

cutting pressure near the end of the cut without re-

laxing your grip on the chain saw handles. Don’t let

the chain contact the ground. After completing the

cut, wait for the saw chain to stop before you move

the chain saw. Always stop the motor before moving

from tree to tree.

Before any work on the machine itself, pull

the mains plug from the socket.

Note: To ensure long and reliable service, carry out

the following maintenance regularly.

Regularly check for obvious defects such as loose,

dislodged or damaged chain and chain bar, loose

fixings and worn or damaged components.

Check that covers and guards are undamaged and

correctly fitted. Carry out necessary maintenance or

repairs before using the chain saw.

If the chain saw should happen to fail despite the

care taken in manufacturing and testing, repair

should be carried out by an authorized customer

service agent.

Before returning, ensure all oil in the oil tank has

been emptied.

For all correspondence and spare parts orders, al-

ways include the 10-digit part number (TYP) from

the nameplate of the machine!

Fit the chain and chain bar as described in “Assem-

bly and Tensioning Chain”.

The circular groove of the chain bar will wear partic-

ularly on the lower edge with time. When replacing

the chain turn the chain bar 180° to allow even wear,

thus extending chain bar life.

Check drive sprocket 20. If it is worn out or damaged

due to strain, have it exchanged by an authorized

Bosch service agent.

Have your chain sharpened professionally at your

Bosch approved service agent or sharpen the chain

yourself using the Bosch sharpening kit or a Dremel

power tool with the appropriate grinder (1453), both

available at your Bosch approved service agent. Fol-

low the sharpening instructions supplied with the

sharpening kit.

Proper functioning of the automatic oiler can be

checked by running the chain saw and pointing the

tip of the chain bar towards a piece of cardboard or

paper on the ground. Caution: Do not touch the

ground with the chain. Ensure safety clearance of

20 cm. If an increasing oil pattern developes, the au-

tomatic oiler is operating fine. If there is no oil pat-

tern, despite a full oil reservoir, see “Fault Finding” or

contact your Bosch approved service agent.

Chain and Chain bar

AKE 30 S .......................................... F 016 800 259

AKE 35 S .......................................... F 016 800 260

AKE 40 S .......................................... F 016 800 261

Chain

AKE 30 S .......................................... F 016 800 256

AKE 35 S .......................................... F 016 800 257

AKE 40 S .......................................... F 016 800 258

Cleaning

Chain sharpening/cleaning kit .......... F 016 800 262

Chain oil 1 litre .................................. 2 607 000 181

Maintenance

Replacing/Changing Chain and

Chain Bar

Sharpening Chain

Checking the Automatic Oiler

Accessories

F 016 L70 540.book Seite 8 Montag, 9. Februar 2009 2:37 14

25 • F 016 L70 540 • TMS • 29.01.09

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GKE 40 BCE Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info