Bedienungsanleitung Bosch GKM 18 V-LI Professional (Seite 15 von 235) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

591816

Zoom out

Zoom in

Vorherige Seite

1/235

Nächste Seite

English | 15

Bosch Power Tools 1 609 92A 0PX | (18.11.14)

 When blade is binding, or when interrupting a cut for

any reason, release the trigger and hold the saw mo-

tionless in the material until the blade comes to a com-

plete stop. Never attempt to remove the saw from the

work or pull the saw backward while the blade is in mo-

tion or kickback may occur. Investigate and take correc-

tive actions to eliminate the cause of blade binding.

 When restarting a saw in the workpiece, centre the saw

blade in the kerf and check that saw teeth are not en-

gaged into the material. If saw blade is binding, it may

walk up or kickback from the workpiece as the saw is re-

started.

 Support large panels to minimise the risk of blade

pinching and kickback. Large panels tend to sag under

their own weight. Supports must be placed under the pan-

el on both sides, near the line of cut and near the edge of

the panel.

 Do not use dull or damaged blades. Unsharpened or im-

properly set blades produce narrow kerf causing excessive

friction, blade binding and kickback.

 Blade depth and bevel adjusting locking levers must be

tight and secure before making cut. If blade adjustment

shifts while cutting, it may cause binding and kickback.

 Use extra caution when sawing into existing walls or

other blind areas. The protruding blade may cut objects

that can cause kickback.

Lower guard function

 Check lower guard for proper closing before each use.

Do not operate the saw if lower guard does not move

freely and close instantly. Never clamp or tie the lower

guard into the open position. If saw is accidentally

dropped, lower guard may be bent. Raise the lower guard

with the retracting handle and make sure it moves freely

and does not touch the blade or any other part, in all angles

and depths of cut.

 Check the operation of the lower guard spring. If the

guard and the spring are not operating properly, they

must be serviced before use. Lower guard may operate

sluggishly due to damaged parts, gummy deposits, or a

build-up of debris.

 The lower guard may be retracted manually only for

special cuts such as “plunge cuts and angle cuts”. Raise

the lower guard by retracting the handle and as soon as

the blade enters the material, release the lower guard.

For all other sawing operations, the lower guard should op-

erate automatically.

 Always observe that the lower guard is covering the

blade before placing saw down on bench or floor. An un-

protected, coasting blade will cause the saw to walk back-

wards, cutting whatever is in its path. Be aware of the time

it takes for the blade to stop after switch is released.

Additional safety warnings

 Do not work overhead with the saw. In this manner you

do not have sufficient control over the power tool.

 Use appropriate detectors to determine if utility lines

are hidden in the work area or call the local utility com-

pany for assistance. Contact with electric lines can lead

to fire and electric shock. Damaging a gas line can lead to

explosion. Penetrating a water line causes property dam-

age.

 Do not operate the power tool stationary. It is not de-

signed for operation with a saw table.

 Do not use high speed steel (HSS) saw blades. Such saw

blades can easily break.

 When working with the machine, always hold it firmly

with both hands and provide for a secure stance. The

power tool is guided more secure with both hands.



Secure the workpiece. A workpiece clamped with clamp-

ing devices or in a vice is held more secure than by hand.

 Always wait until the machine has come to a complete

stop before placing it down. The tool insert can jam and

lead to loss of control over the power tool.

 Do not open the battery. Danger of short-circuiting.

Protect the battery against heat, e. g., against

continuous intense sunlight, fire, water, and

moisture. Danger of explosion.

 In case of damage and improper use of the battery, va-

pours may be emitted. Ventilate the area and seek

medical help in case of complaints. The vapours can irri-

tate the respiratory system.

 Use the battery only in conjunction with your Bosch

power tool. This measure alone protects the battery

against dangerous overload.

 The battery can be damaged by pointed objects such as

nails or screwdrivers or by force applied externally. An

internal short circuit can occur and the battery can burn,

smoke, explode or overheat.

Product Description and Specifica-

tions

Read all safety warnings and all instruc-

tions. Failure to follow the warnings and in-

structions may result in electric shock, fire

and/or serious injury.

While reading the operating instructions, unfold the graphics

page for the machine and leave it open.

Intended Use

The power tool is intended for sawing ferrous metals up to a

cutting depth of 50 mm.

The power tool is not intended for working on wood materials.

Product Features

The numbering of the product features refers to the illustra-

tion of the machine on the graphics page.

1 Spindle lock button

2 Blade guard

3 Utility hook

4 Cutting-depth scale

OBJ_BUCH-2231-001.book Page 15 Tuesday, November 18, 2014 3:22 PM

Bosch GKM 18 V-LI Professional Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info