Bedienungsanleitung Bosch GKM 18 V-LI Professional (Seite 18 von 235) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

591816

Zoom out

Zoom in

Vorherige Seite

1/235

Nächste Seite

18 | English

1 609 92A 0PX | (18.11.14) Bosch Power Tools

Operation

Operating Modes

 Before any work on the power tool, remove the battery.

Adjusting the Cutting Depth (see figure B)

 Adjust the cutting depth to the thickness of the work-

piece. Less than a full tooth of the blade teeth should be

visible below the workpiece.

Loosen the clamping lever 10. For a smaller cutting depth,

pull the saw away from the base plate 13; for a larger cutting

depth, push the saw toward the base plate 13. Adjust the de-

sired cutting depth at the cutting-depth scale. Tighten the

clamping lever 10 again.

The tightening tension of the clamping lever 10 can be read-

justed. For this, unscrew the clamping lever 10, and screw it

back again turned offset by at least 30° in anticlockwise direc-

tion.

Cutting Marks

The cutting mark 12 indicates the position of the saw blade

for straight cuts.

For precise cuts, position the circular saw against the work-

piece as shown in the figure. It is best to carry out a trial cut.

Utility Hook (see figure C)

Your tool is equipped with a utility hook 3 for hanging it, e. g.,

to a ladder, etc. Simply fold out the utility hook 3 to the re-

quired position.

 When the tool is hanging by the utility hook, ensure

that the saw blade is protected against unintended

contact. Danger of injury.

Fold the utility hook 3 back in again when you are ready to

continue working.

Starting Operation

Inserting the battery

 Use only original Bosch lithium-ion batteries with the

voltage listed on the nameplate of your power tool.

Using other batteries can lead to injuries and pose a fire

hazard.

Insert the charged battery 9 into the base of the power tool

until the battery is securely locked.

Switching On and Off

To start the machine, first push the lock-off button for the

On/Off switch 6 and then press the On/Off switch 7 and keep

it pressed.

To switch off the machine, release the On/Off switch 7.

Note: For safety reasons, the On/Off switch 7 cannot be

locked; it must remain pressed during the entire operation.

To save energy, only switch the power tool on when using it.

Run-on Brake

An integrated run-on brake reduces the run-on period of the

saw blade after switching off the machine.

Protection Against Deep Discharging

The lithium-ion battery is protected against deep discharging

by the “Electronic Cell Protection (ECP)”. When the battery is

empty, the machine is switched off by means of a protective

circuit: The inserted tool no longer rotates.

Working Advice

Protect saw blades against impact and shock.

Guide the machine evenly and with light feed in the cutting di-

rection. Excessive feed significantly reduces the service life of

the saw blade and can cause damage to the power tool.

Sawing performance and cutting quality depend essentially

on the condition and the tooth form of the saw blade. There-

fore, use only sharp saw blades that are suited for the material

to be worked.

Sawing with Parallel Guide (see figure D)

The parallel guide 14 enables exact cuts along a workpiece

edge and cutting strips of the same dimension.

Sawing with Auxiliary Guide (see figure E)

For sawing large workpieces or straight edges, a board or

strip can be clamped to the workpiece as an auxiliary guide;

the base plate of the circular saw can be guided alongside the

auxiliary guide.

Recommendations for Optimal Handling of the Battery

Protect the battery against moisture and water.

Store the battery only within a temperature range between

–20 °C and 50 °C. As an example, do not leave the battery in

the car in summer.

Occasionally clean the venting slots of the battery using a soft,

clean and dry brush.

A significantly reduced working period after charging indi-

cates that the battery is used and must be replaced.

Observe the notes for disposal.

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine itself (e. g. mainte-

nance, tool change, etc.) as well as during transport

and storage, remove the battery from the power tool.

There is danger of injury when unintentionally actuating

the On/Off switch.

 For safe and proper working, always keep the machine

and ventilation slots clean.

The retracting blade guard must always be able to move freely

and retract automatically. Therefore, always keep the area

around the retracting blade guard clean. Remove dust and

chips by blowing out with compressed air or with a brush.

0°0°

OBJ_BUCH-2231-001.book Page 18 Tuesday, November 18, 2014 3:22 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GKM 18 V-LI Professional Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info