Bedienungsanleitung Bosch GLL 2-80 P Professional (Seite 13 von 220) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

591992

Zoom out

Zoom in

Vorherige Seite

1/220

Nächste Seite

English | 13

Bosch Power Tools 1 609 92A 0KK | (7.5.14)

Assembly

Inserting/Replacing the Batteries

Alkali-manganese batteries are recommended for the mea-

suring tool.

To open the battery lid 10, slide the latch 11 in the direction

of the arrow and fold the battery lid up. Insert the batteries.

When inserting, pay attention to the correct polarity accord-

ing to the representation on the inside of the battery lid.

When the batteries become weak, a single 5 s audio signal will

sound. The battery low indicator 2 continuously flashes red.

The measuring tool can be operated for less then 2 h.

If the batteries are weak when switching on the measuring

tool, the 5 s audio signal will sound directly after switching on

the measuring tool.

Always replace all batteries at the same time. Only use batter-

ies from one brand and with the identical capacity.

 Remove the batteries from the measuring tool when

not using it for extended periods. When storing for ex-

tended periods, the batteries can corrode and self-dis-

charge.

Operation

Initial Operation

 Loud audio signals will sound under certain conditions

while operating the measuring tool. Therefore, keep

the measuring tool away from your ear or other per-

sons. The loud audio signal can cause hearing damage.

 Protect the measuring tool against moisture and direct

sun light.

 Do not subject the measuring tool to extreme tempera-

tures or variations in temperature. As an example, do

not leave it in vehicles for a long time. In case of large vari-

ations in temperature, allow the measuring tool to adjust to

the ambient temperature before putting it into operation.

In case of extreme temperatures or variations in tempera-

ture, the accuracy of the measuring tool can be impaired.

 Avoid heavy impact to or falling down of the measuring

tool. Damage to the measuring tool can impair its accura-

cy. After heavy impact or shock, compare the laser lines or

plumb beams with a known horizontal or vertical reference

line or with already checked plumb points.

 Switch the measuring tool off during transport. When

switching off, the levelling unit, which can be damaged in

case of intense movement, is locked.

Switching On and Off

To switch on the measuring tool, slide the On/Off switch 7 to

the “on” position (when working without automatic level-

ling) or to the “on” position (when working with automat-

ic levelling). Immediately after switching on, the measuring

tool sends laser beams out of the exit openings 1.

 Do not point the laser beam at persons or animals and

do not look into the laser beam yourself, not even from

a large distance.

 Do not leave the switched-on measuring tool unattend-

ed and switch the measuring tool off after use. Other

persons could be blinded by the laser beam.

To switch off the measuring tool, slide the On/Off switch 7 to

the “off” position. When switching off, the levelling unit is

locked.

When exceeding the maximum permitted operating tempera-

ture of 45 °C, the measuring tool switches off to protect the

laser diode. After cooling down, the measuring tool is ready

for operation and can be switched on again.

Deactivating the Automatic Shut-off

When no button on the measuring tool is pressed for approx.

30 minutes, the measuring tool automatically switches off to

save the batteries.

To switch on the measuring tool after automatic shut-off, ei-

ther slide the On/Off switch 7 to the “off” position and then

switch the measuring tool on again or press the operating

mode button 5 once or press the pulse-function button 3

once.

To deactivate the automatic shut-off, keep the operating

mode button 5 pressed for at least 3 s (while the measuring

tool is switched on). Deactivation of the automatic shut-off is

confirmed by brief flashing of the laser beams.

To activate the automatic shut-off, switch the measuring tool

off and then on again or press and hold the operating mode

button 5 for at least 3 s.

Deactivating the Signal Tone

After the measuring tool has been switched on, the audio sig-

nal is always activated.

To deactivate/activate the audio signal, press and hold the

operating mode button 5 and the pulse-function button 3 at

the same time for at least 3 s.

The audio signal activation and deactivation are both con-

firmed by three short beeps.

Operating Modes

The measuring tool has three operating modes between

which you can switch at any time:

– Horizontal operation: generates a horizontal laser plane,

– Vertical operation: generates a vertical laser plane,

– Cross-line operation: generates a horizontal and vertical

laser plane.

Dimensions

(length x width x height)

159 x 54 x 141 mm

Degree of protection

IP 54 (dust and splash

water protected)

Line laser GLL 2-80 P

1) The working range can be decreased by unfavourable environmental

conditions (e.g. direct sun irradiation).

The measuring tool can be clearly identified with the serial number 13

on the type plate.

OBJ_BUCH-907-003.book Page 13 Wednesday, May 7, 2014 1:39 PM

Bosch GLL 2-80 P Professional Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info