Bedienungsanleitung Bosch GMF 1600 CE Professional (Seite 22 von 272) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

593174

Zoom out

Zoom in

Vorherige Seite

1/272

Nächste Seite

22 | English

1 609 92A 0B3 | (30.4.14) Bosch Power Tools

– Shut the clamping lever for the plunge unit/non-plunge

base 22.

– Adjust the required depth-of-cut; see Section “Adjusting

the Depth-of-cut”.

Separating the Routing Motor from the Plunge Unit/Non-

plunge Base (see figure C)

– Open the clamping lever for the plunge base/non-plunge

base 22.

– Pull the routing motor to the stop and and hold it in this po-

sition.

– Press securing latch 21 and pull the routing motor com-

pletely out of the plunge base/non-plunge base. When us-

ing the non-plunge base 3, additionally press clamping le-

ver 25.

Inserting a Router Bit (see figure D)

 It is recommended to wear protective gloves when in-

serting or replacing router bits.

Depending on the application, router bits are available in the

most different designs and qualities.

Router bits made of high speed steel (HSS) are suitable for

the machining of soft materials, e. g. softwood and plastic.

Carbide tipped router bits (HM) are particularly suitable for

hard and abrasive materials, e. g. hardwood and aluminium.

Original router bits from the extensive Bosch accessories pro-

gram are available at your specialist shop.

Use router bits with a shank diameter of 12 mm as far as this

is possible. Only use clean router bits that are in perfect con-

dition.

The router bit can be changed when the routing motor is

mounted in the plunge base/non-plunge base. However, it is

recommended to change the tool with the routing motor dis-

mounted.

– Remove the routing motor from the plunge base/non-

plunge base.

– Press and hold the spindle lock button 27 (). If required,

turn the spindle by hand until the lock engages.

Actuate the spindle lock button 27 only when at a

standstill.

– Loosen the tightening nut 17 with the open-end spanner

28 (size 24 mm) by turning in antclockwise direction ().

– Insert the router bit into the collet. The shank of the router

bit must be immersed at least 20 mm into the collet.

– Tighten the tightening nut 17 with the open-end spanner

28 (size 24 mm) by turning in clockwise direction. Release

the spindle lock button 27.

 Do not insert a router bit with a diameter larger than

50 mm when the guide bushing is not mounted. Such

router bits do not fit through the base plate.

 Do not tighten the tightening nut of the collet without a

router bit inserted. Otherwise the collet can be damaged.

Dust/Chip Extraction

 Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suitable

for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the mate-

rials to be worked.

 Prevent dust accumulation at the workplace. Dusts can

easily ignite.

Mounting the Extraction Adapter to the Plunge Base

(see figure E)

The extraction adapter 30 can be mounted with the hose con-

nection facing toward the front or rear. When the guide-bush-

ing adapter 50 is inserted, it may be required to mount the

guide-bushing adapter turned by 180°, so that the extraction

adapter 30 does not touch the release lever 52. Fasten the

extraction adapter 30 with the 2 knurled screws 29 to the

base plate 13.

To ensure optimum extraction, the extraction adapter 30

must be cleaned regularly.

Mounting the Extraction Adapter to the Non-plunge Base

(see figure F)

The extraction adapter 32 can be mounted with the hose con-

nection facing toward the front or rear. When the guide-bush-

ing adapter 50 is inserted, fasten the extraction adapter 32

with the 2 knurled screws 29 to the base plate 13. For appli-

cations without the guide-bushing adapter 50, firstly mount

the intermediate ring 33 to the extraction adapter 32, as

shown in the figure.

Connecting the Dust Extraction

Insert an extraction hose (Ø 35 mm) 31 (accessory) into the

mounted extraction adapter. Connect the extraction hose 31

to a vacuum cleaner (accessory).

The machine can be plugged directly into the receptacle of a

Bosch all-purpose vacuum cleaner with remote starting con-

trol. The vacuum cleaner starts automatically when the ma-

chine is switched on.

The vacuum cleaner must be suitable for the material being

worked.

When vacuuming dry dust that is especially detrimental to

health or carcinogenic, use a special vacuum cleaner.

Operation

Starting Operation

 Observe correct mains voltage! The voltage of the pow-

er source must agree with the voltage specified on the

nameplate of the machine. Power tools marked with

230 V can also be operated with 220 V.

Preselecting the Speed

The required speed can be preselected with the thumbwheel

15 (also while running).

OBJ_BUCH-1178-004.book Page 22 Wednesday, April 30, 2014 10:24 AM

Bosch GMF 1600 CE Professional Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info