Bedienungsanleitung Bosch GNA 18V-16 E (Seite 12 von 189) (Alle Sprachen)

786451

Zoom out

Zoom in

Vorherige Seite

1/189

Nächste Seite

12 | English

The vibration level and noise emission value given in these

instructions have been measured in accordance with a

standardised measuring procedure and may be used to com-

pare power tools. They may also be used for a preliminary

estimation of vibration and noise emissions.

The stated vibration level and noise emission value repres-

ent the main applications of the power tool. However, if the

power tool is used for other applications, with different ap-

plication tools or is poorly maintained, the vibration level

and noise emission value may differ. This may significantly

increase the vibration and noise emissions over the total

working period.

To estimate vibration and noise emissions accurately, the

times when the tool is switched off or when it is running but

not actually being used should also be taken into account.

This may significantly reduce vibration and noise emissions

over the total working period.

Implement additional safety measures to protect the oper-

ator from the effects of vibration, such as servicing the

power tool and application tools, keeping their hands warm,

and organising workflows correctly.

Rechargeable battery

Bosch sells some cordless power tools without a re-

chargeable battery. You can tell whether a rechargeable bat-

tery is included with the power tool by looking at the pack-

aging.

Charging the battery

uUse only the chargers listed in the technical data. Only

these chargers are matched to the lithium-ion battery of

your power tool.

Note: Lithium-ion rechargeable batteries are supplied par-

tially charged according to international transport regula-

tions. To ensure full rechargeable battery capacity, fully

charge the rechargeable battery before using your tool for

the first time.

Inserting the Battery

Push the charged battery into the battery holder until it

clicks into place.

Removing the Battery

To remove the rechargeable battery, press the battery re-

lease button and pull the battery out. Do not use force to do

this.

The rechargeablebattery has two locking levels to prevent

the battery from falling out if the battery releasebutton is

pressed unintentionally. The rechargeable battery is held in

place by a spring when fitted in the power tool.

Battery charge indicator

The green LEDs on the battery charge indicator indicate the

state of charge of the battery. For safety reasons, it is only

possible to check the state of charge when the power tool is

not in operation.

Press the button for the battery charge indicator or to

show the state of charge. This is also possible when the bat-

tery is removed.

If no LED lights up after pressing the button for the battery

charge indicator, then the battery is defective and must be

replaced.

Battery model GBA 18V...

LED Capacity

3× continuous green light 60–100%

2× continuous green light 30–60%

1× continuous green light 5–30%

1× flashing green light 0–5%

Battery model ProCORE18V...

LED Capacity

5 × continuous green light 80–100%

4 × continuous green light 60–80%

3 × continuous green light 40–60%

2 × continuous green light 20–40%

1 × continuous green light 5–20%

1 × flashing green light 0–5%

Recommendations for Optimal Handling of the

Battery

Protect the battery against moisture and water.

Only store the battery within a temperature range of −20 to

50°C. Do not leave the battery in your car in the summer, for

example.

Occasionally clean the ventilation slots on the battery using a

soft brush that is clean and dry.

A significantly reduced operating time after charging indic-

ates that the battery has deteriorated and must be replaced.

Follow the instructions on correct disposal.

Operation

Starting Operation

Switching On and Off

To switch on the power tool, slide the on/off switch(3) for-

wards so that I appears on the switch.

To switch off the power tool, slide the on/off switch(3)

backwards so that 0 appears on the switch.

Restart protection

The restart protection feature prevents the power tool from

uncontrolled starting after the power supply to it has been

interrupted.

1 609 92A 7AW | (25.02.2022) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GNA 18V-16 E Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info