592529
13
Zoom out
Zoom in
Vorherige Seite
1/159
Nächste Seite
English | 13
Bosch Power Tools 1 609 929 M22 | (8.10.07)
Operation
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V
can also be operated with 220 V.
Switching On and Off
To start the machine, push the On/Off switch 1
forward so that the “I” is indicated on the
switch.
To switch off the machine, push the On/Off
switch 1 toward the rear so that the “0” is indi-
cated on the switch.
Locking/Loosening the Die
For straight cuts, tighten the locking screw 3
using an Allen key (size 2.5 mm) in order to lock
the die 4.
For curved cuts, loosen the locking screw 3. The
die 4 can move freely now and adjusts to the di-
rection of the feed strength.
Working Advice
Apply the machine to the workpiece only when
switched on. Always hold the machine vertical to
the surface of the steel sheet and do not tilt it.
The cut takes place during the upward motion of
the punch. Guide the machine evenly and with
moderate feed in the cutting direction. A too high
feed rate significantly reduces the service life of
the cutting tools and can damage the machine.
If the punch should become wedged during cut-
ting, switch the machine off, relubricate the
punch and release the tension of the steel
sheet. Do not exert force, otherwise the punch
and die will become damaged.
f Wear protective gloves while working and
pay particular attention to the mains cable.
Sharp burrs develop at the cut steel sheet
and can cause injuries to the operator or
damage the mains cable.
f Exercise caution when handling the cutting
chips. The chips have sharp tips that can
cause injuries.
Maximum Steel Sheet Cutting Capacity
The maximum steel sheet cutting capacity d
max
depends on the strength properties of the ma-
terial to be cut.
The machine allows for straight and deformation-
free cutting of metal sheets to the following
thicknesses:
Lubricating/Cooling the Punch
To extend the service life of the punch 5, a lubri-
cating agent with good cooling properties (e.g.
cutting oil) should be used.
Apply a trail of lubricant beads onto the top side
of the metal sheet alongside the intended cut-
ting line. For long periods of continual use or for
work with high frictional wear (e.g. when cut-
ting aluminium), the cutting head should be
immersed into a container with lubricant in
regular intervals.
Cutting along a Cutting Mark or with a Guide
Straight cuts are carried out easier when the
machine is guided alongside a rule.
Contours can be cut by guiding the machine
along a template.
For inside cuts, pre-drilling a hole with a dia-
meter of 16 mm is necessary.
Material Max. strength
property
[N/mm
2
]
d
max
[mm]
Steel 400 2.0
600 1.4
800 1.0
Aluminium 200 2.5
OBJ_BUCH-236-002.book Page 13 Monday, October 8, 2007 11:54 AM
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch GNA 2.0 Professional wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info