Bedienungsanleitung Bosch GNF 20 CA (Seite 22 von 163) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

78975

Zoom out

Zoom in

Vorherige Seite

1/163

Nächste Seite

22 | English

1 609 929 K57 | (27.11.07) Bosch Power Tools

f Always use undamaged wheel flanges that

are of correct diameter for your selected

wheel. Proper wheel flanges support the

wheel thus reducing the possibility of wheel

breakage.

f The outside diameter and the thickness of

your accessory must be within the capacity

rating of your power tool. Incorrectly sized

accessories cannot be adequately guarded

or controlled.

f The arbour size of wheels and flanges must

properly fit the spindle of the power tool.

Wheels and flanges with arbour holes that do

not match the mounting hardware of the

power tool will run out of balance, vibrate ex-

cessively and may cause loss of control.

f Do not use damaged wheels. Before each

use, inspect the wheels for chips and

cracks. If power tool or wheel is dropped,

inspect for damage or install an undamaged

wheel. After inspecting and installing the

wheel, position yourself and bystanders

away from the plane of the rotating wheel

and run the power tool at maximum no load

speed for one minute. Damaged wheels will

normally break apart during this test time.

f Wear personal protective equipment. De-

pending on application, use face shield,

safety goggles or safety glasses. As appro-

priate, wear dust mask, hearing protectors,

gloves and workshop apron capable of stop-

ping small abrasive or workpiece frag-

ments. The eye protection must be capable

of stopping flying debris generated by vari-

ous operations. The dust mask or respirator

must be capable of filtrating particles gener-

ated by your operation. Prolonged exposure

to high intensity noise may cause hearing

loss.

f Keep bystanders a safe distance away from

the work area. Anyone entering the work ar-

ea must wear personal protective equip-

ment. Fragments of workpiece or of a broken

accessory may fly away and cause injury be-

yond immediate area of operation.

f Hold the power tool only by the insulated

gripping surfaces when performing an oper-

ation where the cutting tool may contact

hidden wiring or its own cord. Contact with

a “live” wire will also make exposed metal

parts of the power tool “live” and shock the

operator.

f Position the cord clear of the spinning ac-

cessory. If you lose control of the power tool,

the cord may be cut or snagged and your

hand or arm may be pulled into the spinning

accessory.

f Never lay the power tool down until the ac-

cessory has come to a complete stop. The

spinning accessory may grab the surface and

pull the power tool out of your control.

f Do not run the power tool while carrying it

at your side. Accidental contact with the

spinning accessory could snag your clothing,

pulling the accessory into your body.

f Regularly clean the power tool’s air vents.

The motor’s fan will draw the dust inside the

housing and excessive accumulation of pow-

dered metal may cause electrical hazards.

f Do not operate the power tool near flamma-

ble materials. Sparks could ignite these ma-

terials.

f Do not use accessories that require liquid

coolants. Using water or other liquid cool-

ants may result in electrocution or shock.

Kickback and related warnings

f Kickback is a sudden reaction to a pinched or

snagged rotating wheel. Pinching or snag-

ging causes rapid stalling of the rotating

wheel which in turn causes the uncontrolled

power tool to be forced in the direction op-

posite of the wheel’s rotation at the point of

the binding.

f Maintain a firm grip on the power tool and

position your body and arm to allow you to

resist kickback forces. Always use auxiliary

handle, if provided, for maximum control

over kickback or torque reaction during

start-up. The operator can control torque re-

actions or kickback forces, if proper precau-

tions are taken.

OBJ_BUCH-126-001.book Page 22 Tuesday, November 27, 2007 9:54 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GNF 20 CA Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info