Bedienungsanleitung Bosch GNF 65 A (Seite 13 von 105) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544272

Zoom out

Zoom in

Vorherige Seite

1/105

Nächste Seite

English | 13

Bosch Power Tools 1 609 929 N87 | (13.2.09)

Starting Operation

f Observe correct mains voltage! The voltage

of the power source must agree with the

voltage specified on the nameplate of the

machine.

Switching On and Off

f Before starting the machine, place the pow-

er tool in such a manner on both rear chaser

rollers 3 that the diamond cutting discs do

not touch the workpiece. Otherwise, the

diamond cutting discs can touch the work-

piece, resulting in possible loss of control

over the power tool when switching on.

To start the power tool, press the On/Off switch

1 forward and then down.

To lock-on the pressed On/Off switch 1, push

the On/Off switch 1 further forward.

To switch off the power tool, release the On/Off

switch 1, or when it is locked, briefly press the

On/Off switch 1 and then release it.

Switch Version without Lock-on

(country-specific):

To start the power tool, press the On/Off switch

1 forward and then down.

To switch off the machine, release the On/Off

switch 1.

f Never set down a coasting machine on the

chaser rollers 3, but always aside, so that

the diamond cutting discs can rotate freely

and do not face toward your body.

f Check the diamond cutting discs before

use. The diamond cutting disc(s) must be

mounted properly and be able to rotate

freely. Carry out a test run for at least one

minute without any load. Do not use dia-

mond cutting discs that are damaged, out-

of-balance, or vibrate. Damaged diamond

cutting discs can rupture and lead to injuries.

Reduced starting current

The electronic reduced starting current limits

the power consumption when switching the tool

on and enables operation from a 13 ampere

fuse.

Overload Protection

When overloaded, the motor comes to a stop.

Relieve the load on the machine immediately

and allow to cool down for approx. 30 seconds

at the highest no-load speed.

Restarting Protection

The restarting protection feature prevents un-

controlled restarting of the machine after an in-

terruption in the power supply.

To restart the operation, switch the On/Off

switch 1 to the Off position and start the ma-

chine again.

Note: Check the function of the restarting pro-

tection feature regularly by having the mains

plug pulled during operation and plugged in

again afterwards.

Working Advice

f Exercise caution when cutting slots in

structural walls; see Section “Information

on Structures ”.

f Do not strain the machine so heavily that it

comes to a standstill.

f Clamp the workpiece if it does not remain

stationary due to its own weight.

f The machine may only be used for dry cut-

ting.

f Always guide the machine with both han-

dles. Do not guide or carry the machine by

the elbow.

– Adjust the cutting depth, see section “Pre-se-

lecting the Cutting Depth”. To compensate

inaccuracies that occur when breaking away

the fin, the cutting depth must be set approx.

3 mm deeper than the requested slot depth.

OBJ_BUCH-916-001.book Page 13 Friday, February 13, 2009 11:21 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GNF 65 A Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info