Bedienungsanleitung Bosch GOP 250 CE (Seite 17 von 199) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544113

Zoom out

Zoom in

Vorherige Seite

1/199

Nächste Seite

English | 17

Bosch Power Tools 2 609 932 802 | (14.2.12)

Dust/Chip Extraction

f Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suitable

for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

f Prevent dust accumulation at the workplace. Dusts can

easily ignite.

Connecting the Dust Extraction (see figure A)

For sanding, always connect the dust extraction.

Remove the application tool/accessory when mounting the

dust extraction 16 (accessory).

If required, assemble the parts of the dust extraction 16 as

shown in the figure. Position the assembled dust extraction

onto the machine via the tool holder 4. Turn the dust extrac-

tion in such a manner that the cams of the dust extraction en-

gage into the corresponding recesses on the housing. Fasten

the dust extraction to the machine with the retaining clip 14

as shown in the figure.

Pay attention that the felt ring 13 is undamaged and faces

tightly against the sanding plate 10. Replace a damage felt

ring immediately.

Depending on the machine model, place a vacuum hose 17

(accessory) either directly onto the vacuum connection 15 or

cut off the old hose end, screw the extraction adapter 18 (ac-

cessory) onto the hose end and insert it directly into the vac-

uum connection 15. Connect the vacuum hose 17 with a vac-

uum cleaner (accessory). An overview for the connection of

various vacuum cleaners can be found at the end of these in-

structions.

The vacuum cleaner must be suitable for the material being

worked.

When vacuuming dry dust that is especially detrimental to

health or carcinogenic, use a special vacuum cleaner.

Operation

f Observe correct mains voltage! The voltage of the

power source must agree with the voltage specified on

the nameplate of the machine. Power tools marked

with 230 V can also be operated with 220 V.

Starting Operation

Switching On and Off

To start the machine, push the On/Off switch 1 forward so

that the “I” is indicated on the switch.

To switch off the machine, push the On/Off switch 1 toward

the rear so that the “0” is indicated on the switch.

When not using the power tool, switch it off in order to save

energy.

Preselecting the Orbital Stroke Rate

With the thumbwheel for preselection of the orbital stroke

rate 2, you can preselect the required orbital stroke rate, even

during operation.

The required stroke rate depends on the material and the

working conditions and can be determined through practical

testing.

Working Advice

f Before any work on the machine itself, pull the mains

plug.

f Wait until the machine has come to a standstill before

placing it down.

Note: Do not cover off the venting slots 3 of the machine while

working, as this reduces the working life of the machine.

Operating Principle

Due to the oscillating drive the application tool/accessory

swings up to 20000 times per minute for 2.8° . This allows for

precise work in narrow spaces.

Work with low and uniform application

pressure, otherwise, the working perform-

ance will decline and the application tool

can become blocked.

While working, move the machine back and

forth, so that the application tool does not

heat up excessively and become blocked.

–Paint

– Varnish

– Filling compound

– Filler

For sanding off paint

coarse 40

For sanding primer (e.g., for removing brush dashes, drops

of paint and paint run)

medium 80

100

120

For final sanding of primers before coating

fine 180

240

320

400

Sanding disc Material Application Grain size

OBJ_BUCH-1271-004.book Page 17 Tuesday, February 14, 2012 11:38 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GOP 250 CE Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info