Bedienungsanleitung Bosch GOP 55-36 Professional (Seite 23 von 304) (Alle Sprachen)

640566

Zoom out

Zoom in

Vorherige Seite

1/304

Nächste Seite

English | 23

Bosch Power Tools 1 609 92A 18M | (14.12.15)

Connecting the Dust Extraction (see figure A)

The dust extraction 8 is intended only when working with the

sanding plate 9; it is not of use in combination with other ap-

plication tools.

For sanding, always connect the dust extraction.

To mount the dust extraction 8 (accessory), remove the appli-

cation tool and the depth stop 15.

Slide the dust extraction 8 all the way over the tool holder 4

onto the collar of the power tool. Turn it to the required posi-

tion. Press shut the clamping lever 16 to fix the dust extrac-

tion.

Plug the tool sleeve 18 of the vacuum hose 19 onto the vacu-

um connection 17. Connect the vacuum hose 19 to a vacuum

cleaner (accessory). You will find an overview of connecting

to various vacuum cleaners on the fold-out page.

The vacuum cleaner must be suitable for the material being

worked.

When vacuuming dry dust that is especially detrimental to

health or carcinogenic, use a special vacuum cleaner.

Operation

 Observe correct mains voltage! The voltage of the pow-

er source must agree with the voltage specified on the

nameplate of the machine. Power tools marked with

230 V can also be operated with 220 V.

Starting Operation

Switching On and Off

To start the machine, push the On/Off switch 1 forward so

that the “I” is indicated on the switch.

To switch off the machine, push the On/Off switch 1 toward

the rear so that the “0” is indicated on the switch.

To save energy, only switch the power tool on when using it.

GOP 40-30: The worklight improves visibility in the immedi-

ate work area. It is automatically switched on and off with the

power tool.

 Do not look directly into the work area illumination –

your sight can be temporarily degraded!

Preselecting the Orbital Stroke Rate

With the thumbwheel for preselection of the orbital stroke

rate 2, you can preselect the required orbital stroke rate, even

during operation.

The required stroke rate depends on the material and the

working conditions and can be determined through practical

testing.

Working Advice

 Before any work on the machine itself, pull the mains

plug.

 Wait until the machine has come to a standstill before

placing it down.

Note: Do not cover off the venting slots 3 of the machine while

working, as this reduces the working life of the machine.

Operating Principle

The oscillating drive causes the application tool/accessory to

oscillate back and forth up to 20000 times per minute. This

enables precise work in the tightest of spaces.

Work with low and uniform application

pressure, otherwise, the working perfor-

mance will decline and the application tool

can become blocked.

While working, move the machine back and

forth, so that the application tool does not

heat up excessively and become blocked.

Sawing

 Use only undamaged saw blades that are in perfect con-

dition. Bent or dull saw blades can break, negatively influ-

ence the cut, or lead to kickback.

 When sawing light building materials, observe the stat-

utory provisions and the recommendations of the ma-

terial suppliers.

 Plunge cuts may only be applied to soft materials, such

as wood, gypsum plaster boards, etc.!

Before sawing with HCS saw blades in wood, particle board,

building materials, etc., check these for foreign objects such

as nails, screws, or similar. If required, remove foreign ob-

jects or use BIM saw blades.

Separating

Note: When separating wall tiles take into consideration that

the application tools/accessories wear heavily when used for

longer periods of time.

Sanding

The removal rate and the sanding pattern are primarily deter-

mined by the choice of sanding sheet, the preset oscillation

rate and the applied pressure.

Only flawless sanding sheets achieve good sanding capacity

and extend the service life of the machine.

Pay attention to apply uniform sanding pressure; this increas-

es the working life of the sanding sheets.

Intensifiying the sanding pressure does not lead to an in-

crease of the sanding capacity, but to increased wear of the

machine and the sanding sheet.

For precise on-the-spot sanding of edges, corners and hard to

reach areas, it is also possible to work only with the tip or an

edge of the sanding plate.

When selectively sanding on the spot, the sanding sheet can

heat up considerably. Reduce the orbital stroke rate and the

sanding pressure, and allow the sanding sheet to cool down

regularly.

A sanding sheet that has been used for metal should not be

used for other materials.

Use only original Bosch sanding accessories.

For sanding, always connect the dust extraction.

OBJ_BUCH-2566-001.book Page 23 Monday, December 14, 2015 4:27 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GOP 55-36 Professional Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info